background image

7

INTRODUCTION

INTRODUCTION

Thank You for purchasing this water heater.  Properly installed and 

maintained, it should give you years of trouble free service.

Abbreviations Found In This Instruction Manual:

• 

ANSI - American National Standards Institute

• 

AHRI - Air-Conditioning, Heating and Refrigeration Institute

• 

NEC - National Electrical Code

• 

NFPA - National Fire Protection Association

• 

UL - Underwriters Laboratory

PREPARING FOR THE INSTALLATION

● Before removing any access panels or 

servicing the water heater, make sure 

the  the electrical supply to the water 

heater is turned OFF.

Electrical Shock Hazard

● Failure to follow these instructions can 

result in personal injury or death.

1. 

Read the “General Safety Information” section of this manual 

first and then the entire manual carefully. If you don’t follow the 

safety rules, the water heater may not operate safely. It could 

cause 

DEATH, SERIOUS BODILY INJURY AND/OR PROPERTY 

DAMAGE

.

This manual contains instructions for the installation, operation, 

and maintenance of the electric water heater.  It also contains 

warnings throughout the manual that you must read and be 

aware of.  All warnings and all instructions are essential to the 

proper operation of the water heater and your safety.  

READ 

THE ENTIRE MANUAL BEFORE ATTEMPTING TO INSTALL OR 

OPERATE THE WATER HEATER.

Be sure to turn off power when working on or near the electrical 

system of the heater. Never touch electrical components with 

wet hands or when standing in water. When replacing fuses 

always use the correct size for the circuit. See 

Wiring Diagram 

(page 23).

The  model  and  rating  plate  on  page  9  interprets  certain 

markings  into  useful  information.  Both  of  these  references 

should  be  used  to  identify  the  heater,  its  components  and 

optional equipment.

2. 

The installation must conform with these instructions and the 

local code authority having jurisdiction and the requirements of 

the power company. In the absence of local codes, the installation 

must comply with the latest editions of the

 National Electrical 

Code, NFPA 70

 or the 

Canadian Electrical Code CSA C22.1. 

The 

National 

Electrical Code

  may  be  ordered  from:  National  Fire  Protection 

Association,  1  Batterymarch  Park,  Quincy,  MA  02269. The 

Canadian Electrical Code

 is available from the Canadian Standards 

Association, 8501 East Pleasant Valley Road, Cleveland, OH 

44131.

3. 

If after reading this manual you have any questions or do not 

understand any portion of the instructions, call the toll free number 

listed on the back cover (page 24) of this manual for technical 

assistance. 
A  sample  rating  plate  is  shown  in 

Model and Rating

  (page  9). 

In order to expedite your request, please have full model and 

serial number available for the technician.

4. 

Carefully  plan  your  intended  placement  of  the  water  heater.  

Examine the location to ensure the water heater complies with 

Locating the Water Heater 

(page 10).

Installation  and  service  of  this  water  heater  requires  ability 

equivalent to that of a licensed tradesman or qualified agency  

in the field involved. Plumbing and electrical work are required.  

See 

Important Definitions 

(page 3).

Printed on 7/25/2022 7:17 AM CT

Summary of Contents for Compact 10

























Reviews: