American Standard ACONT900AC43UA Installer'S Manual Download Page 11

ACONT900AC43UA

Pub. No. 11-HD04D1-2

11

69-2080—05

2nd Stage Heater 
Defrost Balance 
Point

0362

40

0, 5 - 55

0 - Disabled
5 - 5°F (-15.0°C)
10 - 10°F (-12.0°C)
15 - 15°F (-9.5°C)
20 - 20°F (-6.5°C)
25 - 25°F (-4.0°C)
30 - 30°F (-1.0°C)
35 - 35°F (1.5°C)
40 - 40°F (4.5°C)
45 - 45°F (7.0°C)
50 - 50°F (10.0°C)
55 - 55°F (13.0°C)

Only shown if outdoor 
temperature is available.

3rd Stage Heater 
Defrost Balance 
Point

0363

25

0, 5 - 55

0 - Disabled
5 - 5°F (-15.0°C)
10 - 10°F (-12.0°C)
15 - 15°F (-9.5°C)
20 - 20°F (-6.5°C)
25 - 25°F (-4.0°C)
30 - 30°F (-1.0°C)
35 - 35°F (1.5°C)
40 - 40°F (4.5°C)
45 - 45°F (7.0°C)
50 - 50°F (10.0°C)
55 - 55°F (13.0°C)

Only shown if outdoor 
temperature is available.

Defrost Heater 
Selection

0364

0 - 7

0 - None
1 - Aux1
2 - Aux2
3 - Aux3
4 - Aux1 and Aux2
5 - Aux2 and Aux3
6 - Aux1 and Aux3
7 - Aux1 and Aux2 and
Aux3

Default will be preset to the 
maximum number of aux 
heat stages available.
Only shown if Heater 
Defrost Balance Point(s) 
are disabled by selecting 
“0” in ISU 0361, 0362 and/
or 0363.

Discharge 
Temperature Sensor

0365

E

E, 0, 1

E - Auto-Discover
0 - None
1 - Remote Sensor
Installed

For future use.
Leave at factory
default setting “E”

Indoor Humidity 
Sensor

0370

1

0, 1, 2

0 - Disabled
1 - Internal sensor
2 - Remote sensor

Indoor Humidification 
Control

0372

E, 0

E, 0, 1, 2 E - Auto-Discover

0 - Off
1 - Relative Humidity
Setpoint
2 - Dewpoint Control

Auto-Discover will discover 
“0”
Dewpoint Control with Frost 
Protection requires outdoor 
temperature sensor

Humidifier Fan Action 0374

2

1, 2

1 - Fan turns on with
Humidifier
2 - Humidify only when
Heat is on

Only visible when ISU 0372 
enabled. Fan will run for 2 
minutes after humidifier 
turns off.

Indoor 
Dehumidification 
Control

0380

1

0, 1, 4

0 - Off
1 - Integrated Temperature
and Humidity Control -
ITHC (RH Setpoint)
4 - American Standard 
Heating & Air Conditioning 
Droop (RH
Setpoint)

Deadband limited when in 
Auto- Changeover Mode 
and ITHC is enabled. See 
“Dehumidification” on 
page 19.

Comfort-R

TM 

Delay

0381

0

0, 1, 2

0 - No Delay

Comfort-R

TM 

15

 

sec

2 - Comfort-R

TM

 

30 sec

Only shown for non-variable 
speed indoor units

Dehumidification 
Maximum Droop

0383

1

1, 2, 3

1 - 1°F (0.5°C)
2 - 2.0°F (1.0°C)
3 - 3°F (1.5°C)

Only shown if ITHC is 
selected

Table 4. Installer Setup Menu

Selection

Installer Setup 

Number (ISU)

Factory 

Setting

Choices

Comments

Option

Description

Summary of Contents for ACONT900AC43UA

























Reviews: