American Hometec AHG-T42-LP Installation And Operation Manual Download Page 47

    

Page 47 

 
Limited Warranty 

Register unit at www.AmericanHometec.com

 

General

 

The manufacturer warrants this water heater and its components to be free from defects in 
material and workmanship according to the terms herein. 

The heat exchanger within this product is warranted against manufacturer defects for up to 
10 years for residential water heating applications or up to 5 years for commercial and industrial 
applications. The remaining components of the unit are warranted against manufacturer defects 
for a period of 12 months from date of purchase if it is a residential application.  The warranty is 
to the original owner of the equipment at original installed location and is transferable only with 
original receipt showing date of purchase. The warranty applies to heaters installed within the 
US and Canada by licensed professionals in accordance with the manufacturer’s installation and 
operating instructions and all applicable codes. The warranty covers parts for the repair or 
replacement of the defective portions of the unit and, for residential applications only, labor for 
a period of 12 months. The effective date of the warranty is the verified date of purchase 
(original receipt) or the date of manufacture plus ninety days. 

Exclusion

 

THIS LIMITED WARRANTY SHALL BE THE EXCLUSIVE WARRANTY MADE BY THE MANUFACTURER 
AND IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED (WHETHER WRITTEN 
OR ORAL), INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY AND FITNESS 
FOR A PARTICULAR PURPOSE. THE REMEDIES SET FORTH HEREIN ARE THE ONLY REMEDIES 
AVAILABLE TO THE OWNER OR ANY PERSON. The company does not authorize any person or 
company to assume any obligation or liability in connection with the repair or replacement. 
Manufacturer shall not be liable for any incidental, consequential, special or contingent damages 
or expenses arising, directly or indirectly, from any defect in the water heater or the use of the 
water heater. Manufacturer shall not be liable for any water damage arising, directly or indirectly, 
from any defect in the water heater component part(s) or from its use. 

Manufacturer shall not be liable under this warranty if the water heater is subjected to any of the 
following conditions. 

 

Misuse, alteration, unauthorized repair, neglect, accident 

 

Has not been installed in accordance with the applicable local plumbing and/or building 
code(s) and/or regulation(s) 

 

Is not continuously supplied with potable water 

 

Has been operated while frozen 

 

Is exposed to inlet temperatures above 125

o

F (52

o

C) 

 

Exposed to water pressures above pressure rating of 150 psig (1.0 MPa) 

 

Used for service in a spa, pool, boat or water craft 

 

If burner had been opened 
 

Summary of Contents for AHG-T42-LP

















































Reviews: