American Hometec AHG-T42-LP Installation And Operation Manual Download Page 1

 

 

Gas Tankless Water Heater 

Installation and Operation Manual 

Model AHG-T42 

 

 

American Hometec, Inc. 
3411 Silverside Road 
Hanby Building 
Wilmington, DE 19810 

 

WARNING: If the information in these instructions is not followed exactly, a fire or 
explosion may result causing property damage, personal injury or death. 

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any 
other appliance. 

- WHAT TO DO IF YOU SMELL GAS: 
 

• 

Do not try to light any appliance.  

 

• 

Do not touch any electrical switch; do not use any phone in your building. 

 

• 

Immediately call your gas supplier from a neighbor’s phone. 

 

• 

Follow the gas supplier’s instructions.  

 

• 

If you cannot reach your gas supplier, call the fire department. 

- Installation and service must be performed by a qualified installer, service agency or the gas 
supplier. 

- Water heater for other than recreational vehicle installation only. 

 

www.AmericanHometec.com

 

[email protected]

 

Toll Free: 1

-

800

-

295

-

8039

 

 
 

 

Summary of Contents for AHG-T42-LP

















































Reviews: