American Hearth ADVD32FP3(0,1,2,3)(N,P)-1 Installation Instructions And Owner'S Manual Download

Page: 53 / 60

23574-5-0608

Page 53

CAUTION: ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE WITH

ALL LOCAL, CITY AND STATE BUILDING CODES. BEFORE MAKING THE ELECTRICAL CONNECTION, MAKE

SURE THAT MAIN POWER SUPPLY IS DISCONNECTED. THE APPLIANCE, WHEN INSTALLED, MUST BE ELECTRI-

CALLY GROUNDED IN ACCORDANCE WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES, WITH THE

NATIONAL ELECTRICAL CODE ANSI/NFPA 70 (LATEST EDITION).

A factory installed junction box is located on the lower right

side of the ﬁreplace. Wiring must be fed to the junction box and

attached to the receptacle that is provided. Leave approximately

6" of wire in the junction box for connection.
Attach black wire to one side of the receptacle and white wire to

opposite side of receptacle. The ground wire should be attached

to the green (ground) screw.
Install the receptacle into the junction box. Attach cover plate.

1. Using gloves, unpack liner components and check for

damaged or missing components.

2. Lower bottom louver and remove upper louver on ﬁreplace.

3. Remove glass frame assembly from ﬁreplace.

4. Remove rear logs from burner assembly.

5. Place brick panel (rear) against rear wall in ﬁreplace.

Note: The top edge will have a half-moon cutout relief to match

up with the rear ﬂue vent hole.

6. While holding the front ﬁnished edge of a side brick panel

(left & right), place brick panel (sides) against side walls in

ﬁreplace. NOTE: The side brick panels should be installed

with full brick pattern at the bottom. Move side panels

rearward until the back edge meets the rear brick panel. Slide

side brick panels down so they rest on ﬁrebox bottom, and

brick joints match up with the back brick panel.

7. Align grout lines on top brick panel with the grout lines on the

side brick panels. Place the top brick panel into brick panel

holder. With needle-nose pliers, carefully bend hold-down tabs

on brick panel holder over the edges of the top brick panel.

The hold-down tabs will securely hold the top brick panel in

place.

8. Replace rear logs onto burner assembly. (Refer to log

placement, pages 36 and 37.

9. Attach glass frame assembly onto ﬁreplace.

10. Raise bottom louver and replace top louver onto ﬁreplace.

11. Installation of optional brick liner is complete.

1. To wire Junction Box Receptacle, remove the tab on the side

of the receptacle (hot side) to split receptacle. This will be

required to separate blower and valve circuits.

2. Power for switched and live sides of Duplex Receptacle must

come from the same power source. (One circuit breaker on

main panel must switch all power off.)

3. From the wall box to the ﬁreplace a 3-wire conductor with

ground is recommended, however (2) two-wire conductors

with grounds may be used in place of a 3-wire conductor with

a ground if the black wires from the thermostat and blower

switch are identiﬁed.

4. Two wall switches, or a wall switch and thermostat may be

used to activate the two receptacle plugs independently.

JUNCTION BOX WIRING INSTALLATION INSTRUCTIONS

OPTIONAL BRICK LINER INSTALLATION INSTRUCTIONS

120V DIRECT IGNITION VALVE MODELS

STANDARD MILLIVOLT VALVE MODELS

Summary of Contents for ADVD32FP3(0,1,2,3)(N,P)-1





























































Search results

Summary of Contents for ADVD32FP3(0,1,2,3)(N,P)-1

Reviews:

Related manuals for ADVD32FP3(0,1,2,3)(N,P)-1

Brands by name

Popular brands

American Hearth ADVD32FP3(0,1,2,3)(N,P)-1, Installation Instructions And Owner'S Manual

Search results

Summary of Contents for ADVD32FP3(0,1,2,3)(N,P)-1

Reviews:

Related manuals for ADVD32FP3(0,1,2,3)(N,P)-1

Brands by name

Popular brands