manualshive.com logo in svg

American Dynamics ADC780, Installation And Setup Manual

Share
Download
American Dynamics ADC780 Installation And Setup Manual Download Page 7

ADC780 SERIES VANDAL-RESISTANT CAMERA 

8000-2811-01, REV. C1 

INSTALLATION AND SETUP GUIDE  

7 of 11 

Heater Installation  

Corner Mount  

Remove the ac terminal block and wiring to the AC 
camera connection and replace it with the thermo-
stat PC board and heater element. Each compon-
ent is held in place by two screws. For wiring 
details, see ac/heater wiring diagram on page 8. 

 

 

Surface Mount  

Remove the ac terminal block and wiring to the AC 
camera connection and replace it with the thermo-
stat PC board and heater element. Each compon-
ent is held in place by two screws. For wiring 
details, see ac/heater wiring diagram on page 8. 

 

Heater/Fan  
Installation 

(Surface Mount only) 

Remove the ac terminal block and wiring to the AC 
camera connection and replace it with the thermo-
stat PC board and the heater/fan assembly. Each 
component is held in place by two screws. For 
wiring details, see ac/heater/fan wiring diagram on 
page 8. 

 

AC Terminal Block 

Heater  
Element 

Thermostat  
PC Board 

AC Camera Connection 

Thermostat  
PC Board 

Heater  
Element 

AC Terminal Block 

AC Camera 
Connection 

Summary of Contents for ADC780












Reviews:

No comments

Brands by name

Popular brands

Load more brands