manualshive.com logo in svg

American Dryer Corp. ML-190, Installation Manual, Page: 8 / 62

Share
Download
American Dryer Corp. ML-190 Installation Manual Download Page 8

4

American Dryer Corp.

113354 - 20

WARNING:

Disconnect power before resetting the hi-limit.  The hi-limit is located on the left side of
the burner box, looking at the burner from the back of the dryer.  Press and release and
the hi-limit will reset.

CE ONLY

IMPORTANT:

This appliance must only be installed and operated in the country of destination
indicated on the dryer’s data plate.  If the appliance is to be installed and operated in a
country other than the one indicated on the data plate, a data plate amendment must
be obtained from American Dryer Corporation.

IEC335 applies.

  NOTES ______________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________________

Summary of Contents for ML-190































































Reviews:

No comments