manualshive.com logo in svg

American Dryer Corp. ML-190, Installation Manual, Page: 32 / 62

Share
Download
American Dryer Corp. ML-190 Installation Manual Download Page 32

28

American Dryer Corp.

113354 - 20

Shaded areas are stated in metric equivalent

* Drill Measurement Size (D.M.S.) equivalents are as follows:
** Check dryers rating plate.

Natural Gas .............................. #1 = 0.2280” (5.7912 mm).

#6 = 0.2040” (5.1816 mm) for 190 (AGA)

..................................................

#13 = 0.1850” (4.699 mm) for 190DR.

L.P. Gas .................................... #28 = 0.1405” (3.5687 mm).

#31 = 0.1200 (3.048 mm) for 190 (AGA).

..................................................

#33 = 0.1130” (2.870 mm) for 190DR.

2. Technical Data

a. Gas Specifications

TYPE OF GAS

NATURAL

LIQUID PROPANE

  Manifold Pressure*

3.5 inches W.C.

8.7 mb

10.5 inches W.C.

26.1 mb

  In-Line Pressure

6.0 - 12.0 inches W.C.

14.92 - 29.9 mb

11.0 inches W.C.

27.4 mb

TYPE OF GAS

Liquid

Propane

Conversion Kit

Part Number

Btu/hr

**

Rating

kcal/hr

Rating

Natural

Liquid Propane

Qty.

D.M.S.

*

Part No. Qty.

D.M.S.

*

Part No.

590,000

148,680

4

#1

140840

4

#28

140821

882222

470,000

118,517

4

#6

140833

4

#31

140818

887249

404,000

101,874

4

#13

140860

4

#33

140855

882252

Shaded areas are stated in metric equivalents

*  Measured at the gas valve pressure tap when the gas valve is on.

b. Gas Connections:

Inlet connection -------------- 1-1/2” N.P.T.
Inlet supply size -------------- 1-1/2” Pipe (minimum)
Btu/hr input (per dryer) ---- 590,000 (148,680 kcal/hr)

----------------------------------

470,000 (118,517 kcal/hr) for MLG-190 (AGA)

----------------------------------

404,000 (101,874 kcal/hr) for MLG-190DR

1) Natural Gas

Regulation is controlled by the dryer’s gas valve’s internal regulator.  Incoming supply pressure

must be

 consistent between a minimum of 6.0 inches (14.92 mb) and a maximum of 12.0 inches

(29.9 mb) water column (W.C.) pressure.

2) Liquid Propane (L.P.) Gas

Dryers made for use with L.P. gas have the gas valve’s internal pressure regulator blocked open so
that the gas pressure 

must be

 regulated upstream of the dryer.  The pressure measured at each

gas valve pressure tap 

must be

 a consistent 10.5 inches (26.1 mb) water column.  There is no

regulator or regulation provided in an L.P. dryer.  The water column pressure 

must be

 regulated at

the source (L.P. tank) or an external regulator 

must be

 added to each dryer.

Summary of Contents for ML-190































































Reviews:

No comments