manualshive.com logo in svg

American Dryer Corp. ML-190, Installation Manual

Share
Download
American Dryer Corp. ML-190 Installation Manual Download Page 28

24

American Dryer Corp.

113354 - 20

GAS AND STEAM

ELECTRICAL SERVICE SPECIFICATIONS

  

IMPORTANT

:

  

NOTES

: A.

 B.
 
 
 C.

208 VAC AND 230/240 VAC ARE NOT THE SAME.  When ordering,
specify exact voltage.

When fuses are used they must be dual element, time delay, current

limiting, class RK1 or RK5 ONLY.  Calculate/determine correct fuse

value, by applying either local and/or National Electrical Codes to

listed appliance amp draw data.
Circuit breakers are thermal-magnetic (industrial) motor curve type
ONLY.  For others, calculate/verify correct breaker size according to
appliance amp draw rating and type of breaker used.
Circuit breakers for 3-phase (3ø) dryers must be 3-pole type.

SERVICE

VOLTAGE

PHASE

WIRE

SERVICE

APPROX.

AMP DRAW

CIRCUIT

BREAKER

60 Hz

50 Hz

208

3ø

3

37

—

50

220

3ø

3

35

36

50

230

3ø

3

34

—

50

230

3ø

3

—

30

40

240

3ø

3

35

—

50

380

3ø

3

19

—

30

380

3ø

 4

*

—

18

30

400 / 416

3ø

 4

*

—

17

30

460 / 480

3ø

3

19

—

30

575

3ø

3

14

—

20

IMPORTANT:

The dryer 

must be

 connected to the electric supply shown on the data label.  In the

case of 208 VAC or 240 VAC, the supply voltage must match the electric service
specifications of the data label 

exactly

.

WARNING: 208 VAC AND 240 VAC ARE

 

NOT

 

THE

 

SAME.

  Any damage done to dryer

components due to improper voltage connections will automatically VOID THE
WARRANTY.

NOTE: ADC

 reserves the right to make changes in specifications at any time without notice or

obligation.

2. Electrical Service Specifications

8/20/14

*  3 Wire is available.

8/20/14

ELECTRIC

ELECTRICAL SERVICE SPECIFICATIONS

  

IMPORTANT

:

  

NOTES

: A.

 B.
 
 
 C.

208 VAC AND 230/240 VAC ARE NOT THE SAME.  When ordering,
specify exact voltage.

When fuses are used they must be dual element, time delay, current

limiting, class RK1 or RK5 ONLY.  Calculate/determine correct fuse

value, by applying either local and/or National Electrical Codes to

listed appliance amp draw data.
Circuit breakers are thermal-magnetic (industrial) type ONLY.  For
others, calculate/verify correct breaker size according to appliance
amp draw rating and type of breaker used.
Circuit breakers for 3-phase (3ø) dryers must be 3-pole type.

SERVICE

VOLTAGE

PHASE

WIRE

SERVICE

OVEN

kW

APPROX.

AMP DRAW

CIRCUIT

BREAKER

60 Hz

50 Hz

220

3ø

3

106

312

—

400

240

3ø

3

126

338

—

425

Summary of Contents for ML-190































































Reviews:

No comments

Brands by name

Popular brands

Load more brands