manualshive.com logo in svg

American Dryer Corp. ML-190, Installation Manual, Page: 29 / 62

Share
Download
American Dryer Corp. ML-190 Installation Manual Download Page 29

113354 - 20

www.adclaundry.com

25

3. Electrical Connections

NOTE:

A wire diagram is included with each dryer and is affixed to the back side of the top control
(access) door.

The only electrical input connections to the dryer are the 3-phase (3ø) power leads (L1, L2, and L3),
GROUND, and in the case of 4 wire service, the NEUTRAL.  These electrical connections are made at
the terminal block located in the service/relay box at the rear, upper left hand corner of the dryer.  To gain
access into this service box, the service cover 

must be

 removed.

The “LINE POWER” and the “GROUND” connections to the dryer 

must be

 made through the knockout

hole at the top of the electric service/relay box.  A strain relief 

must be

 used where the line power ground

wires go into the electric service/relay box.

Providing local codes permit, power connections to the dryer can be made by use of a flexible underwriters
laboratory list cord/pigtail (wire 

must conform

 to ratings of the dryer), or the dryer can be hard wired

directly to the service breaker.  In 

ALL

 cases, a strain relief 

must be

 used where the wire(s) enter the

dryer’s electrical service (relay) box.

NOTE: A CIRCUIT SERVICING EACH DRYER 

MUST BE

 PROVIDED

.

Summary of Contents for ML-190































































Reviews:

No comments