![background image](http://html1.mh-extra.com/html/american-dj/vizi-roller-beam-2r/vizi-roller-beam-2r_user-instructions_2923238014.webp)
ADJ Products, LLC - www.adj.com - Vizi Roller Beam 2R Instruction Manual Page 27
ADJ Products, LLC - www.adj.com - Vizi Roller Beam 2R Instruction Manual Page 26
Vizi Roller Beam 2R
System Menu
Vizi Roller Beam 2R
System Menu
ENTER.
2. Press the UP or DOWN buttons until “Status Setting” is dis-
played, press ENTER.
3. Press UP or DOWN buttons, until “Address via DMX” is dis-
played, and press ENTER.
4. Either “Off” or “On” will be displayed, use the UP and DOWN but-
tons to toggle between.
5. Press ENTER to confirm your selection or press MODE/ESC to
exit.
To use this function follow these instructions:
To adjust the address of your unit you must first go to the address
that it is currently set to. From there you can adjust the address. First
make sure all channels are set to the value of “0”.
1. On your DMX controller set the DMX value of Channel 1 to the
value “7”.
2. Now set the DMX value of Channel 2 to the value “7” to adjust the
starting address between 1 and 255. To adjust the address between
256 and 511 set Channel 2 to the value “8” .
3. Set the DMX value of Channel 3 to your desired starting address.
This will take about 20 seconds before the unit accepts the new DMX
address.
EXAMPLE: If you want the address to be 57, you must first set the
address that is currently assingned to the unit. Then set Channel 1’s
value to “7”, Channel 2’s value to “7”, and Channel 3’s value to “57”.
Wait 20 seconds and the address should change on the unit to “57”.
2ND EXAMPLE: If you want the address to be 420, you must first set
the address that is currently assingned to the unit. If you want the set
the address to 420, set Channel 1’s value to “7”, Channel 2’s value to
“8”, and Channel 3’s to “164”. (256 + 164 = 420).
No DMX status - With this function if the DMX signal is suddenly
lost, the unit will automatically go into 1 of 3 modes.
1. Press the MODE/ESC button to access the main menu. Press the
UP or DOWN buttons so that “Personality” is highlighted, then press
ENTER.
2. Press the UP or DOWN buttons until “Status Setting” is dis-
played, press ENTER.
3. Press UP or DOWN buttons, until “No DMX Status” is displayed,
and press ENTER.
4. Either “Hold” (Last DMX setting), “Close” (Blackout), “Music”
(Sound Active), or “Auto” (Auto Program) will be displayed, use the
UP and DOWN buttons to toggle between.
5. Press ENTER to confirm your selection or press MODE/ESC to
exit.
No DMX status - With this function if the DMX signal is suddenly
lost, the unit will automatically go into 1 of 3 modes.
1. Press the MODE/ESC button to access the main menu. Press the
UP or DOWN buttons so that “Personality” is highlighted, then press
ENTER.
2. Press the UP or DOWN buttons until “Status Setting” is dis-
played, press ENTER.
3. Press UP or DOWN buttons, until “No DMX Status” is displayed,
and press ENTER.
4. Either “Hold” (Last DMX setting), “Close” (Blackout), “Music”
(Sound Active), or “Auto” (Auto Program) will be displayed, use the
UP and DOWN buttons to toggle between.
5. Press ENTER to confirm your selection or press MODE/ESC to
exit.
Pan Reverse - With this function you can reverse the Pan movement.
1. Press the MODE/ESC button to access the main menu. Press the
UP or DOWN buttons so that “Personality” is highlighted, then press
ENTER.
2. Press the UP or DOWN buttons until “Status Setting” is dis-
played, press ENTER.