background image

Unpacking: 

Thank you for purchasing the Illusion Dotz 4.4 by ADJ 

Products, LLC. Every Illusion Dotz 4.4 has been thoroughly tested and 

has been shipped in perfect operating condition. Carefully check the 

shipping carton for damage that may have occurred during shipping. 

If the carton appears to be damaged, carefully inspect your fixture for 

any damage and be sure all equipment necessary to operate the unit 

has arrived intact. In the event damage has been found or parts are 

missing, please contact our toll free customer support number for fur-

ther instructions. Please do not return this unit to your dealer without 

contacting customer support first. 

Introduction: 

The Illusion Dotz 4.4 is a DMX intelligent, moving head 

fixture. The Illusion Dotz 4.4 can be a 12 channel, 14 channel, or 59 

Channel DMX unit. The fixture can operate in three different operating 

modes; show mode, sound-

active, or 

under DMX control

The Illusion 

Dotz 4.4 can be used as a stand alone unit or in a

 master/slave con

-

figuration.

 For best results use fog or special effects smoke to enhance 

the beams projections. 

Customer Support:

  ADJ  Products,  LLC  provides  a  toll  free  cus-

tomer support line, to provide help and to answer any question should 

you encounter problems during your set up or initial operation. You 

may also visit us on the web at www.adj.com for any comments or 

suggestions. Service Hours are Monday through Friday 8:00 a.m. to 

4:30 p.m. Pacific Standard Time.

 

Voice:   

(800) 322-6337

 

Fax:    

(323) 582-2610

 

E-mail:  

[email protected]

Warning! 

To prevent or reduce the risk of electrical shock or fire, do 

not expose this unit to rain or moisture. 

Warning! 

This may cause severe eye damage. Avoid looking directly 

into the light source at all times!

  Illusion Dotz 4.4         

                             General Information

ADJ Products, LLC  -  www.adj.com  - Illusion Dotz 4.4 Instruction Manual Page 3

ADJ Products, LLC  -  www.adj.com  - Illusion Dotz 4.4 Instruction Manual Page 2

Table of Contents

Unpacking......................................................................3

Introduction....................................................................3

Customer  Support......................................................................3

Safety Precautions......................................................................4

Features.........................................................................5

Handling Precautions..................................................................6

Registration......................................................................6

Mounting.........................................................................7-8

DMX Set-Up...........................................................................9-11

System Menu............................................................................12

Operation............................................................................31-32

Kling-Net/ArtNet Control...........................................................33

DMX Traits............................................................................34-44

Fuse Replacement....................................................................46

Cleaning..................................................................46

Trouble Shooting.......................................................................46

Warranty.........................................................................47

Specifications....................................................................50

Summary of Contents for Illusion Dotz 4.4



























Reviews: