©
American DJ
®
- www.americandj.com - Galaxian Gem LED Instruction Manual Page 8
©
American DJ
®
- www.americandj.com - Galaxian Gem LED Instruction Manual Page 7
Galaxian Gem LED
Laser Warning Labels
Galaxian Gem LED
Set Up
Power Supply:
The American DJ
®
Galaxian Gem LED contains a
automatic voltage switch, which will auto sense the voltage when it
is plugged into the power source. With this switch there is no need
to worry about the correct power voltage, this unit can be plugged in
anywhere.
DMX-512:
DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fix-
ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking:
DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a sin-
gle controller, as long as all fixtures and the controller are DMX com-
pliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. Therefore, the first fixture controlled by the
controller could be the last fixture in the chain. When a fixture is as-
signed a DMX address of 1, the DMX controller knows to send DATA
assigned to address 1 to that unit, no matter where it is located in the
DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation):
The Galaxian Gem LED can be controlled via DMX-512
protocol. The Galaxian Gem LED is a five channel
DMX unit. The DMX address is set electronically
using the controls on the rear panel of the unit. Your
unit and your DMX controller require a approved
DMX-512 110 Ohm Data cable for data input and
data output (Figure 1). We recommend Accu-Cable
DMX cables. If you are making your own cables, be
sure to use standard 110-120 Ohm shielded cable
(This cable may be purchased at almost all profes-
sional sound and lighting stores). Your cables should be made with
Figure 1
CAUTION - CLASS 3R
LASER RADIATION WHEN OPEN
AVOID DIRECT EYE EXPOSURE
12
m
m
40mm
AVOID EXPOSURE
LASER RADIATION
IS EMITTED FROM
THIS APERTURE
20
m
m
40mm
17
m
m
40mm
American DJ Supply,Inc.
6122 S.Eastern Ave.
Los Angeles. CA 90040 USA
Manufactured:
SPEC LABEL
LASER RADIATION AVOID
DIRECT EYE EXPOSURE
Maximum output <5 mW
Wavelength: 532nm
Class IIIa laser product
This device complies with 21 CFR chapter I,
Subchapter J, or CFR 1040.10 and 1040.11
30
m
m
41 mm
AVOID EXPOSURE
LASER RADIATION
IS EMITTED FROM
THIS APERTURE
American DJ Supply,Inc.
6122 S.Eastern Ave.
Los Angeles. CA 90040 USA
Manufactured:
CAUTION - CLASS 3R
LASER RADIATION WHEN OPEN
AVOID DIRECT EYE EXPOSURE
LASER RADIATION AVOID
DIRECT EYE EXPOSURE
Maximum output <5 mW
Wavelength: 532nm
Class IIIa laser product
This device complies with 21 CFR chapter I,
Subchapter J, or CFR 1040.10 and 1040.11
SPEC LABEL
