©
American DJ
®
- www
.americandj.com - Flight Moon™ Instruction Manual Page 1
1
©
American DJ
®
- www
.americandj.com - Flight Moon™ Instruction Manual Page 12
Flight Moon™
Set Up
Figure 3
1 Ground
1 Ground
XLR Male Socket
XLR Pin Confi
guration
3 Hot
2 Cold
2 Cold
3 Hot
XLR Female Socket
Pin 3 = Data
T
rue (positive)
Pin 2 = Data Compliment (negative)
Pin 1 = Ground
Special Note: Line T
ermination.
When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior
.
A
terminator is a 90-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DA
T
A
+ and
DA
T
A
-).
This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior
.
1
2
3
Te
rmination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin XLR
connectors for DA
T
A
transmission in place of 3-pin. 5-pin XLR fi
xtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores.
The chart
below details a proper cable conversion.
Conductor
5-Pin XLR Male (In)
3-Pin XLR Female (Out)
Pin 1
Do Not Use
Do Not Use
Pin 3
Pin 2
Pin 1
Pin 3
Pin 2
Not Used
Not Used
Data T
rue
(+
signal)
Data Compliment (- signal)
Ground/Shield
3-Pin XLR to 5-Pin XLR Conversion
Flight Moon™
Fuse & Lamp Replacement
Ca
u
tio
n
:
Alwa
y
s
r
e
p
lac
e wit
h
t
h
e e
x
ac
t s
a
me type l
a
m
p
an
d fu
s
e
,
unless otherwise s
p
e
c
if
ied b
y
an a
u
thor
iz
ed Amer
ic
an D
J
®
te
c
h
n
ic
ian.
Re
plac
e with an
ythi
ng other than the s
p
e
c
ifie
d pa
rt c
a
n d
a
mag
e
y
o
ur
unit
a
n
d wi
ll v
o
id
y
o
ur manuf
a
c
tur
es wa
rrant
y.
Wa
rn
in
g
:
If
, afte
r r
e
p
la
c
in
g t
h
e l
a
m
p
o
r fu
s
e
e
ith
e
r o
n
e c
o
n
tin
u
e
s
to b
low
, S
T
OP u
s
in
g the u
n
it. Co
ntac
t c
u
sto
m
er su
p
p
ort f
o
r f
u
rther
ins
tru
c
tions, y
o
u ma
y ha
v
e
to r
e
tur
n
the u
n
it f
o
r serv
ic
in
g. Conti
n
ui
ng
to use the u
n
it ma
y c
a
use ser
ious d
a
mag
e
.
Fu
s
e
R
e
p
la
c
e
m
e
n
t:
D
is
c
o
n
n
e
c
t t
h
e
u
n
it’s
m
a
in po
w
e
r sup
p
ly
. Inse
rt
a st
anda
rd fla
t hea
d
scre
w driv
e
r in t
o
the fuse holde
r housing. T
u
rn
the
scre
w
d
riv
e
r in
c
ount
e
r-
c
lo
c
k
w
is
e d
ir
e
c
tio
n t
o
r
e
m
o
v
e
t
h
e f
u
s
e
holde
r. Remo
v
e
the fuse holde
r t
o
e
x
pose the fuse
. Remo
v
e
the old
fuse and disc
a
rd it. Replac
e the fuse with the same t
y
pe
. Inse
rt the
fuse holde
r bac
k
in
to
it
’s
housing and tu
rn
it in c
lo
c
k
w
ise di
rec
tion t
o
lo
c
k
the holde
r in plac
e
.
Lamp Replacement:
Caution! Never attempt to
change the lamp
while the fixture is plugged in.
Always disconnect the main power and
allow
the
unit
ample
time
to
cool
before
attempting
to
replace
the
lamp. Lamp replacement has been made simple by incorporating the
use of a flip-up front cover that is retained by thumb screws.
1.
Be sure to follow the proper handling procedures that deal
with halogen lamps.
2.
Remove the thumb screw on the top/rear of the unit that holds the
lamp socket assembly cover in place.
3.
After removing the thumb screw
, slide out the cove from the rear of
the unit to expose the lamp socket assembly.
4.
Carefully remove the old lamp and discard it in the trash.
5.
Replace the lamp with an exact match and reassemble in reverse
order
.
Ha
lo
ge
n
L
a
m
p
Wa
rn
in
g
:
This
fixture
is
fitted
with
halogen
lamps
which
are
highly
susceptible
to damage if improperly handled. Never touch the
lamps
with
your
bare
fingers
as
the
oil
from
your
hands will shorten lamp life.
Also, never move the
fixture until the lamps have had ample time to cool.
Remember
, lamps are not covered under warranty
conditions.
