©
American DJ
®
- www
.americandj.com - Flight Moon™ Instruction Manual Page 10
©
American DJ
®
- www
.americandj.com - Flight Moon™ Instruction Manual Page 9
Power Supply:
Before plugging your unit in, be sure the source volt-
age in your area matches the required voltage for your
American DJ
®
Flight Moon.™
The
American DJ
®
Flight Moon
™
is available in a 120v
and 220v version. Because line voltage may vary from venue to venue,
you should be sure your unit voltages matches the wall outlet voltage
before attempting to operate you fi
xture.
DMX-512:
DMX
is
short
for
Digital
Multiplex.
This
is
a
universal
protocol used as a form of communication between intelligent fixtures
and controllers.
A
DMX controller sends DMX data instructions from
the
controller
to
the
fixture.
DMX
data
is
sent
as
serial
data
that
travels from fixture to fixture via the DA
T
A
“IN” and DA
T
A
“OUT” XLR
terminals
located
on
all
DMX
fixtures
(most
controllers
only
have
a
DA
T
A
“OUT”
terminal).
DMX Linking:
DMX is a language allowing all makes and models of
dif
ferent manufactures to be linked together and operate from a single
controller
, as long as all fi
xtures and the controller are DMX compliant.
To
ensure proper DMX data transmission, when using several DMX
fixtures try to use the shortest cable path possible.
The order in which
fixtures
are
connected
in
a
DMX
line
does
not
influence
the
DMX
addressing. For example; a fixture assigned a DMX address of 1 may
be placed anywhere in a DMX line, at the beginning, at the end, or
anywhere in the middle. When a fixture is assigned a DMX address of
1, the DMX controller knows to send DA
T
A
assigned to address 1 to
that unit, no matter where it is located in the DMX chain.
Dip-switches in DMX mode:
This unit uses dip switches to assign a
DMX address. Each dip switch represents a binary value.
Dip Switch 1 address equals 1
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
Dip Switch 7 address equals 64
Dip Switch 8 address equals 128
Dip Switch 9 address equals 256
Dip
Switch
10
-
Some
unit
omit
dip
switch
10,
when
a
unit
does
Flight Moon™
Set Up
ON
19
8
7
6
5
4
3
2
10
128
28
32
256
65
16
4
1
SP
DMX CHANNEL
Flight Moon™
Set Up
Figure 1
Notice:
Be sure to follow fi
gures two and three when making your own
cables. Do not use the ground lug on the XLR connector
. Do not con-
nect the cable’
s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’
s
outer casing. Grounding
the shield could cause a short circuit and erratic behavior
.
DMX512 IN
3-PIN XLR
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Figure 2
included dip switch 10 it is used for special functions such as sound
activation.
Each dip switch has a preset value.
A
specific DMX address is set by
combining the dipswitches that sum your desired value. For example:
To
achieve a DMX address of 21, combine dip switches 1, 3, and 5.
Sense
dipswitch
1
has
a
value
of
1,
dipswitch
3
has
a
value
of
4,
and dipswitch 5 has a value of 16
, the combination of the create a
DMX value of 21.
Set DMX address 21:
Set DMX address 201:
Dipswitch # 1 = 1
Dipswitch # 1 = 1
Dipswitch # 3 = 4
Dipswitch # 4 = 8
Dipswitch # 5 = 16
Dipswitch # 7 = 64
= 21
Dipswitch # 8 = 128
= 201
Data Cable (DMX Cable) Requirements (For DMX and Master/
Slave Operation):
The Flight Moon™ can be controlled via DMX-512
protocol. The
American
DJ
®
Flight Moon™ is a two channel DMX unit.
The DMX address is set on the front panel of the Flight Moon™.
Y
our
unit and your DMX controller require a standard
3-pin XLR connector for data input and data output
(Figure 1). If you are making your own cables, be
sure to use standard two conductor shielded cable
(This cable may be purchased at almost all pro
sound and lighting stores).
Y
our cables should be
made with a male and female XLR connector on
either end of the cable.
Also remember that DMX
cable must be daisy chained and can not be split.
