Accu Spot 300
Fuse & Lamp Replacement
Caution:
Always replace with the exact same type lamp and fuse,
unless otherwise specified by an authorized American DJ
®
service
technician. Replacing with anything other than the specified part can
damage your unit and will void your manufactures warranty.
Warning:
If you continue to blow lamps or fuses, STOP using the
unit. Contact customer support for further instructions, you may have
to return the unit for servicing. Continuing to use the unit may cause
serious damage.
Lamp Replacement:
Caution! Never attempt to change the lamp
while the fixture is plugged in. Always disconnect the main power
and allow the unit ample time to cool before attempting to replace the
lamp. Lamp replacement has been made simple by incorporating the
a slide out lamp assembly that is retained by two phillips screws.
1. Be sure to follow the proper handling procedures that deal with
discharge lamps.
2. Remove the two small screws (A,B) on the rear of the unit
3. After removing the screws, gently slide out the socket assembly
from the rear of the unit to expose the lamp.
4. Carefully remove the old lamp and discard it in the trash.
5. Replace the lamp with an exact match and reassemble in reverse
order.
6. After replacing the lamp follow the optimization procedures on the
next page to be sure the lamp is center in the reflector
A
B
Accu Spot 300
Operation
Stand-Alone (Sound Active or Auto Program):
This mode allows
a single unit to run to the beat of the music or run through a built-in
program.
1. Access the main menu.
2. Tap the UP button until
“
PLAY
” is displayed, and Press ENTER.
3.
Tap the UP button until “
AUTO
” is displayed, and Press ENTER.
4. Press UP, to select “
OFF
”, “
RUN
”, or “
AUDI
”. “
RUN
” will make the
unit run through a built-in program. “
AUDI
” will make the unit
sound active.
5. Select a mode, and press ENTER to confirm.
6. Press MODE/ESC if you want to return to the main menu.
7. You may change the show or invert the pan and tilt functions
in the system menu by following the directions on pages 20-21.
Master-Slave Operation (Sound Active or Auto Program):
This function will allow you to link up to 16 units together and oper-
ate without a controller. The units can run a built-in program or run in
sound actiive mode. In Master-Slave operation one unit will act as the
controlling unit and the others will react to the controlling units pro-
grams. Any unit can act as a Master or as a Slave.
1. Using standard XLR microphone cables, daisy chain your units
together via the XLR connector on the rear of the units. Remem-
ber the Male XLR connector is the input and the Female XLR
connector is the output. The first unit in the chain (master) will use
the female XLR connector only - The last unit in the chain will use
the male XLR connector only. For longer cable runs we suggest a
terminator at the last fixture.
2. Access the main menu.
2. Tap the UP button until
“
PLAY
” is displayed, and Press ENTER.
3.
Tap the UP button to choose between “
RUN
” or “
AUDI
”. “
RUN
” will
make the units run through a built-in program. “
AUDI
” will make
the units sound active.
4. Press UP, to select “
ALON
” or “
NAST
”. Which means stand alone,
or master/slave mode.
5. Select a mode, and press ENTER to confirm.
6. Press MODE/ESC if you want to return to the main menu
7. You may change the show or invert the pan and tilt functions
in the system menu by following the directions on pages 20-21.
American DJ
®
- www.americandj.com - Accu Spot 300 Instruction Manual Page 35
American DJ
®
- www.americandj.com - Accu Spot 300 Instruction Manual Page 36
