background image

diagram 24

diagram 27

1/4” gap

3/8”

door to pan 

threshold

clearance

shower pan

top of shower pan threshold

glass panels

to bottom

of door

to inside

of shower

E - Install Glass Door & Header
 

1.  The glass panels and header pieces are secured with silicone.  

  2.  Apply a 1/4” thick bead of silicone into the bottom of the glass channels in the pan and in the  

    wall thresholds.
  3.  Re-install the glass panel in the same way you did before. Do this for the other panel as well.
  4.  Refer back to all of the previous steps and diagrams to make sure the glass panels are in the  

    proper position. Apply a 1/4” thick bead of silicone into the bottom channel of the header.
  5.  Apply a 1/4” thick bead into the bottom channel of the header center piece.
  6.  Have someone help set door into position, don’t forget to install the washer into hinge pin
  7.  Set header into position, don’t forget to install washer on hinge pin. Check alignment and  

   spacing.
  8.  Locate the wall threshold trim caps and install them using the same procedure for installing the  

    wall threshold trim pieces. 

(diagram 25) 

  9.  Locate the header side pieces and apply a 1/4” bead of silicone to the top of the glass  

    channels. Place them into position and push them all the way down onto the glass panels.  

    Be sure to align them to the header center section. 

(diagram 26)

 

10.  Allow the silicone to dry before continuing with the installation. Make sure the glass remains in  

    the proper position. Leave the door in the closed position and use braces to support the glass  

    until the silicone dries. Refer to the manufacturer’s instructions for silicone drying time.

F - Door Seal Installation  

We have provided door seals for water sensitive areas such as wood floors. If glass panels and door 

are installed correctly with the proper spacing, outside water spillage will be minimal and the side 

seals won’t be necessary. The door sweep 

(diagram 27) 

is what keeps the door closed. Adjust tension 

as needed. If you would like to use these side seals, follow the steps below.

  1.  Locate the plastic H shaped seals. One goes on the glass panel on the door strike side

    the other goes on the door on the hinge side. Measure and cut the seals to length. 

  2.  Starting from the top, push the seal onto the glass, slowly working your way down.

  3.  When you grout the rest of the shower, be sure to grout the extra hinge hole in the pan and the  

    extra hinge hole in the stone header. Also, grout between the glass and the pan, the glass and  

    the wall thresholds, and the glass and the stone header. As well as between the joints between  

    the stone header center section and side pieces.

diagram 25

diagram 26

threshold trim cap

caps

door sweep

12

Summary of Contents for Sistine Stone Neo Corner-Hnf















Reviews: