5
6
G
NOW YOU ARE READY TO FLY!
If you have successfully synced your ASC-2080 to your controller as explained on page 4 you are now ready to
fly. Before beginning to fly your drone you should familiarize yourself with how to start and stop the rotors,
how to use your auto land feature and how the controls work so please carefully read and familiarize yourself
with the various control features explained in the next. Once again as a beginner pilot you should learn how
to control your drone in a large open field or park on a day with zero or very light wind. Do not try to fly your
ASC-2080 too high until you become a more experience pilot.
Even though the ASC-2080 has four rotors there is still a front or
"forward" facing direction and "rear" or backwards facing direction. The
front and forward facing direction of the ASC-2080 is the side with a
camera. The rear and backward facing direction of the drone is the side with
a red light (see diagram G).
FRONT
REAR
RECOGNIZING THE FRONT & REAR OF THE ASC-2080
SPEED SELECT BUTTON
The ASC-2080 has 4 speed settings; T(Training),1 (SLOW), 2 (MEDIUM) and 3 (HIGH). The Default setting
when you first turn on your ASC-2080 is the 1 (SLOW) speed mode. To increase the speed simply trigger the
speed setting button (see remote diagram on pg 3) you will hear beeping sounds of the controller will show
you what speed setting you are on. Speed settings can be set before flight or during the flight.
Fixed-Point Landing
Square Pattern Maneuver
Cross Pattern Maneuver
FLIGHT PRACTICE
To master flying your ASC-2080 drone try practicing the exercises shown below, start with simple vertical
takeoffs, landings, and left/right turning and rotating. Once those are mastered move on to square and
cross maneuvers. Good luck and have fun!
I
J
K
L
FLIGHT CONTROL
Below is a list of basic flight functions for your long-range remote to control the ASC-2080. While
learning to fly your ASC-2080 it is best to start in a large space with the drone facing away from you until
you get used to the basic controls. As you master flying your ASC-2080 you can move to more advanced
maneuvering techniques. Practice makes perfect!
Move the left Throttle stick up to increase the
propeller speed and the ASC-2080 will ascend.
Move the left Throttle stick down to decrease the
propeller speed and the ASC-2080 will descend
(see diagram I).
While in the air, move the left throttle stick
directly left and the ASC-2080 will rotate
horizontally left (counter clockwise)
Move the left throttle stick directly right and the
ASC-2080 will rotate horizontally right
(see
diagram J).
While in the air, move the right direction control
stick forward and the ASC-2080 will move
forward.
Move the right direction control stick backwards
and the ASC-2080 will move backward
(see
diagram K).
While in the air, move the right direction control stick
to the left and the ASC-2080 will bank/sweep to the
left.
Move the right direction control stick to the right
and the ASC-2080 will bank/sweep to the right
(see diagram L).
H1
H2
H2
AUTOMATICALLY TAKE OFF / LAND
Make sure you have properly synced The ASC-2080.
• simply press the Auto Start/Land button, your ASC-2080 will
automatically take off.
• To stop or land the ASC-2080 just Press the Auto Start/Land button
again and the ASC-2080 will descend and land automatically
(see diagram H1).
Tips: You also can move the two control sticks simultaneously down inside or outside corners, hold them till
the blades start spinning. Release the control sticks and push the throttle stick slowly to take off manually
(see diagram H2).
T (Training)MODE & OBSTACLE AVOIDANCE TRAINING FEATURE
Simply press and hold the Speed Button for 2 seconds, you will hear a long beep indicating you are in T
Mode. T mode allows you to learn how to operate your ASC-2080 at a very slow speed. Also there are
maximum and minim height limits set to avoid crashing into the ceiling or floor.
New obstacle avoidance training feature will cause the drone to automatically circumvent walls and other
obstructions so new pilots can get the hang of flying. Set the ASC-2080 speed in the T(Training) speed mode
and the obstacle avoidance feature will start working.
Note: the obstacle avoidance feature only works for T(Training) mode.
