Amatrol 890-FTS1 Manual Download Page 10

Page: 10 / 12

L17401-CL06JEN-E2-S02, REV. C INTRODUCTION TO TROUBLESHOOTING
Copyright © 2019 Amatrol, Inc.

S02-10

SKILL 2 TEST A MANUAL SWITCH



16. Perform the following substeps to test the upper set of contacts of selector

switch SS1 using the out-of-circuit test procedures.

A. Rotate the selector switch

SS1

operator to the center position.

In this position, the upper contacts of this switch should be open.

B. Place the multimeter leads into the terminals of the upper contacts of SS1,

as shown in fi gure 2-6, and record the measurement.

SS1 Resistance (operator in center) ______________________ (Ohms)

If the contacts are good, the resistance should be infi nite (open). This is
the fi rst step of testing the selector switch. The next step is to test it when
the operator is switched.

Figure 2-6. Selector Switch SS1 Contacts Test Method

COM

OPERATOR STATION

PN 17320

EARTH

GND

SS1

PB3

PB2

PB1

Summary of Contents for 890-FTS1













Search results

Summary of Contents for 890-FTS1

Reviews:

Related manuals for 890-FTS1

Brands by name

Popular brands

Amatrol 890-FTS1, Manual

Search results

Summary of Contents for 890-FTS1

Reviews:

Related manuals for 890-FTS1

Brands by name

Popular brands