background image

L17401-CL06JEN-E2-S02, REV. C   INTRODUCTION TO TROUBLESHOOTING
Copyright © 2019 Amatrol, Inc.

S02-5

SKILL 2   TEST A MANUAL SWITCH 

B.  If you are using the FaultPro Troubleshooting System, turn on the system.

C. Start up the FaultPro software and login using your ID number and 

password.

D. If necessary, open the Class folder by clicking the 

+

 to the left of the class 

name.

E. Open the 

LAP 6: Introduction to Troubleshooting

 option.

F. Select the 

Skill 2: Test a Manual Switch

 option. 

G. Click the 

Single Fault Mode

 button.

 

The FaultPro software will open the Single Fault Mode window. 

H. Type 

6

 in the Enter Fault fi eld.

I. Press the 

Enter

 key or click 

 to activate the fault.

 

Fault 6 is now active. You should observe that the fault status fi eld changes 
from “No Faults Active” to “Fault 6 is Active.”

 

Fault 6 is a short in the N.O. contacts of PB1.

J.  Repeat step 4 to test the pushbutton and record your measurements.

PB1 Resistance (not pressed)  ___________________________ (Ohms)

PB1 Resistance (pressed) _______________________________ (Ohms)

Component Status  _________________________________ (Good/Bad)

 

This time you should fi nd that the multimeter measures zero resistance 
in both conditions. This means that there is a short in the contacts. The 
component is bad.

K. Click the 

Clear Fault

 button to clear the fault or remove the fault plug.

 

With the FaultPro software, the fault will clear and the fault status fi eld 
should change to “Fault 6 is cleared.”

  If you are using manual fault insertion, remove the short plug from 

terminal 6 and replace it with the standard jumper plug.

L.  Repeat the pushbutton test in step 4.

PB1 Resistance (not pressed)  ___________________________ (Ohms)

PB1 Resistance (pressed)  ______________________________ (Ohms)

Component Status  _________________________________ (Good/Bad)

 

The resistance should change this time when the pushbutton is pressed. 
This means it is good again.

 

Now proceed to the next substep to test an open type fault in N.O. contacts.

M. If you are using manual fault insertion, locate the open fault plug and plug 

it into station fault terminal 7. Then, go to substep P. If you are using the 
FaultPro software, continue with substep N.

N. Type 

7

 to insert fault 7 in the Enter Fault fi eld.

Summary of Contents for 890-FTS1













Reviews: