Amatrol 890-FTS1 Manual Download Page 11 | Manualshive

Page: 11 / 12

background image

L17401-CL06JEN-E2-S02, REV. C INTRODUCTION TO TROUBLESHOOTING
Copyright © 2019 Amatrol, Inc.

S02-11

SKILL 2 TEST A MANUAL SWITCH

Again, this relates to the contact block, as fi gure 2-7 shows.

Figure 2-7. Actual Measurement of Contacts

C. Rotate the selector switch to the left position and record the resistance.

SS1 Resistance (operator in left) ________________________ (Ohms)

If the contacts are good, the resistance should be at or near zero. This

shows that the contacts are closing when the operator is switched. This
selector switch should be good.

COM

Ω

Ω

N.O. CONTACT

BLOCK

«
...
9
10
11
12
»

Summary of Contents for 890-FTS1













Reviews:

No comments

Related manuals for 890-FTS1

Univerge SV8100

Brand: NEC Pages: 2

Brand: Farris Engineering Pages: 12

Brand: Eastern Times Technology Pages: 4

Brand: Vacon Pages: 18

SolarCell Remote

Brand: Samsung Pages: 2

Brand: Datavideo Pages: 17

Brand: Datamax Pages: 22

Brand: LAIA Pages: 71

Brand: fakro Pages: 16

Brand: e-BLEACH Pages: 24

Brand: Samson Pages: 48

Brand: Fox Pages: 5

Brand: Aulisa Pages: 32

J1000 CIMR-JC series

Brand: YASKAWA Pages: 26

Brand: Netro Pages: 14

Brand: phytron Pages: 55

Brand: National Instruments Pages: 5

Brand: M-system Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands