Pro Tips
Wire can be hidden
by running the wires through a hole behind the wall mounting plate and along
the back side of the drywall to a location with an outlet.
Switching to battery only power mode
can be done by restarting the keypad with the battery
power. First, remove wall power supply and batteries. Wait 10 seconds. Then, power the keypad
back up with only batteries. In battery only power mode, AC failure will not be indicated.
Unenrollment
can be done by following the same steps as enrollment.
Force unenroll
can be done when no panel is present. Hold the 1 and 3 keys simultaneously to
enter unenrollment mode. After the keypad fails to unenroll, hold the 1 and 3 keys simultaneously
again to force unenroll.
AC loss
will cause an AC fail trouble condition after 1 minute and will switch to battery operation
blinking display after 10 minutes of continued AC loss.
Adjust blink rate
by holding the Instant Arm button and pressing the * or # key. This can only be
done when the device is operating in battery only mode and is not tampered. Blink interval
options are Off, 10 seconds (default), 5 seconds, and 2.5 seconds. A portion of the light bar will
illuminate to indicate how much feedback will be given.
Specifications
Physical
Wall Dimensions
Table Top Footprint
Weight
Mounting Fasteners
Pilot Hole for Screw into Wood
Pilot Hole for Wall Anchor
3.81 x 5.10 x 1.55 inches (9.68 x 12.94 x 3.94 cm)
3.81 x 5.47 x 3.17 inches (9.68 x 13.89 x 8.05 cm)
1.49 lb (675 g)
#6 screws & 2 wall anchors (included)
Ø 1/8 in (3 mm)
Ø 3/16 in (4.7 mm)
Environmental
Operating Temperature
Maximum Humidity
32 to 120°F (0 to 49°C)
85% relative humidity non-condensing
Device Specifications
Frequency
Power Supply
Input
Output
Part Number
Replacement Battery
Nominal Battery Life
Current Draw
Transmitted Indications
2.4 GHz
100-240VAC, 50/60Hz, 0.5A
12VDC, 1A
RE012-6
4 AA batteries
1 year (Battery only operation under normal use)
350mA (Maximum)
Low Battery, Supervision, Tamper, AC Fail
Certification
RE663
FCC, IC
Specifications subject to change without notice.
IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC: 8310A-RE663
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by Alula could void
the user’s authority to operate this equipment.
FCC ID: U5X-RE663
TRADEMARKS
Alula and are trademarks owned by Alula Holdings, LLC.
47-00012 • REV A • 2021-04-13
Tech Support Line • (888) 88-ALULA • (888) 882-5852
alula.com
01
