background image

Note: This product is designed to be installed and serviced by security and lock industry professionals.

Specifications

Case Dimensions:

6

1

/

2

”L x 1

3

/

4

”W x 1

1

/

8

”D

Electrical:

 

Voltage: 5-12VDC (reader)
12-24VAC/DC (controller)

Current (max): 120mA

Relay Contacts:

Main Relay (controller): 2A 

Aux Relays (controller): 1A

Bell Relay:
Form A; 1 Amp @ 30VDC; 
500mA @ 125VAC

Environmental:

-20 º F to 130° F

Features

Vandal Resistant Case

Sealed for Indoor or Outdoor Applications

LED's for Relay Status Indication

Bell Output

Surface Mount

Illuminated Hardened Keys

Rated for Greater than One Million Key Cycles

Applications

Low to Medium/Heavy Traffic Areas

Rough Service Environments

Mullion Frame Mounting

Dimly Lit Areas

Description:

The 232iLM Access Control unit consists of two pieces: an
SSWiLM keypad front end and a 232 Access Control
Module.  IEI's Door-Gard Series SSWiLM keypad combines
elegant looks with a  mullion mount design in a rugged,
vandal resistant case, which you can use for almost any
application.  The SSWiLM has hardened backlit keys
designed to perform in medium to high traffic areas and in
rough duty environments.  The electronics are also
conformal coated, which makes the keypad suitable for
indoor or outdoor applications.

Basic Operation:

To gain access through the door enter your code (1-6 digits)
followed by the * key on the keypad.

Packing List:

(1) SSWiLM Keypad
(1) IEI 232 Controller
(1) Eight-Conductor Wire Harness
(4) Three-Conductor Wire Harness
(1) Controller Hardware Pack
(1) Mullion Hardware Pack
(1) 

5

/

64

” Allen Wrench

(1) Anti-Oxidant Grease Pack
(1) Installation/Programming Manual
(1) Self-Contained Access Control Programming Guide

Wire Harness Configuration:

Pin

Wire Color

Signal Name

1

Red

Power (+)

2

Black

Power (-)

3

White/Black

Data 0

4

White/Yellow

Data 1

5

Blue

Not Used

6

Brown

Not Used

7

White

Bell Relay Contact (A)

8

White

Bell Relay Contact (B)

Wiring Requirements:

18 AWG – 1000 Ft.
20 AWG – 500 Ft.
22 AWG – 250 Ft.

Document # 6050800 Rev 1.1

               1 of  12

      www.ieib.com

232iLM Keypad Installation and Programming Instructions

Summary of Contents for 232iLM













Reviews: