- 2 -
eBridge8PCRX
Overview:
The eBridge8PCRX is a CAT5 to Coax cable Managed Ethernet Midspan receiver. The receiver enables fast 10/100Base-T
Ethernet digital communication to be received over Coax cable. An eBridge8PCRX receiver sends power over the coax to
the eBridge1PCT 15.4W (PoE) or eBridge1PCTX 30W (PoE+) transmitter under PoE protocol. The eBridge1PCT/PCTX
in turn delivers that power to a PoE enabled camera or IP device. The eBridge8PCRX will not deliver power to non com-
pliant devices, thus avoiding accidental power turn into improperly connected analog cameras. These plug and play units
facilitate system upgrades from analog to IP cameras/devices utilizing existing legacy Coax and eliminating the costs and
labor associated with installing new network cabling. In addition, data transmission and power over the Coax is possible
up to 500m in comparison to 100m Ethernet maximum distance (see Maximum Length of Coax Type vs. Camera Power/
PoE Class, pg. 3). A maximum range from head end to the PoE camera/device is 610m taking into consideration that up
to 100m of structured cable may be deployed at each end.
Features:
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and
authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application.
eBridge8PCRX is not intended to be connected to outside plant leads and should be installed indoors within the protected
premises. The eBridge8PCRX is intended for indoor use only. This product is intended to be supplied by a UL Listed
Power Supply rated from 48VDC to 56VDC.
Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of
the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equip-
ment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe
operation of the equipment is not compromised
Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved
due to uneven mechanical loading.
Circuit Overloading - Consideration should be given to the connection of the equipment to supply circuit and the effect
that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of
equipment nameplate rating should be used when addressing this concern.
Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be
given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).
Agency Listings:
• UL/CUL Listed for Information
Technology Equipment (UL 60950-1).
• CE approved.
Input:
• 48VDC to 56VDC UL Listed power supply
(attention to observe polarity).
Note: Use 54V to 56V power supply to achieve full
power per IEEE802.3 at standard.
Power Consumption
(per input for max. load; 2 inputs, each powers 8 channels)
:
• 48VDC/6A, 56VDC/6A,
eBridge1PCTX (30W): Powered by eBridge8PCRX.
eBridge1PCT (15W): Powered by eBridge8PCRX.
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair Cat-5 or better structured cable.
• Distance: up to 100m.
• Speed: 10/100BaseT, half/full duplex, auto negotiation.
• Throughput is rated to pass 25mbps of data at
distances up to 500m. With proper headend
equipment multiple Megapixel cameras can be used.
Coax:
• Distance: up to 500m.
• Connectivity: BNC, RG-59/U or similar.
LED Indicators:
• Blue LED - Coax link connection.
• Yellow and Green LED (RJ45) IP Link status,
10/100Base-T/active.
• Green LED - Power.
Environmental:
• Operating Temperature: 14ºF to 122ºF (--- 10ºC to +50ºC).
• Storage Temperature: -- 22º to 158ºF (--- 30º to +70ºC).
• Humidity: 20 to 85%, non-condensing
Applications:
• Retrofit digital IP cameras in an analog CCTV
installation.
• Works with Megapixel, HD720, HD1080 and VGA
(SD) cameras (see note, pg. 2).
• Extend Network link distance in an industrial
environment.
• Upgrade deployed CCTV Coax to a digital network
for Retail, Casinos, Airports, Schools, Hospitals, etc.
Mechanical:
• Dimensions (H x W x D approx.):
1.625” x 19.125” x 8.5” (42mm x 486mm x 216mm)
