- 2 -
eBridge100RM
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and
with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or
Recognized wire suitable for the application.
eBridge100TM/eBridge100ST and eBridge100RM are not intended to be connected to outside
plant leads and should be installed indoors within the protected premises. eBridge100TM,
eBridge100ST, and eBridge100RM are intended for indoor use only.
Note: The eBridge100RM can be paired with either eBridge100TM or eBridge100ST.
1.
eBridge100RM installation:
a. Secure unit to desired mounting surface with a proper fastening device utilizing the unit’s
mounting
hole
(Fig. 2a, pg. 3). Unit should be mounted in proximity to ethernet
switch/network, NVR or video server.
Note: When installing more than one (1) eBridge100RM, please allow at least 1” (25mm)
distance between the receivers.
b.
Connect structured cable from Ethernet midspan or endspan device to RJ45 jack marked
[PoE
Input]
(Fig. 2, pg. 3).
c.
When connecting to the eBridge100 transceiver:
Coax: Connect Coax cable to BNC connector marked [Coax] (Fig. 2, pg. 3).
CAT5 or higher: Connect CAT5 or higher to connector marked [RJ45 OUT]
(eBridge100TM
only)
(Fig. 2, pg. 3).
2.
eBridge100TM installation:
a. Secure unit to desired mounting surface with a proper fastening device utilizing the case’s
mounting
hole
(Fig. 2a, pg. 3). Unit should be mounted in proximity of camera/device.
b. Connect structured cable from IP camera/device to RJ45 jack marked [PoE Out] (Fig. 2, pg. 3).
c.
Coax: Connect Coax cable to BNC connector marked [Coax] (Fig. 2, pg. 3).
CAT5 or higher: Connect CAT5 or higher to connector marked [RJ45 IN] (Fig. 2, pg. 3).
3.
eBridge100ST installation:
a. Secure unit to desired mounting surface with a proper fastening device utilizing the case’s
mounting
hole
(Fig. 3, pg. 3). Unit should be mounted in proximity of camera/device.
b. Connect structured cable from IP camera/device to RJ45 jack marked [PoE Out] (Fig. 3, pg. 3).
c.
Coax: Connect Coax cable to BNC flying lead marked [Coax] (Fig. 3, pg. 3).
Note: The eBridge100RMT is designed to accommodate Megapixel, HD720, HD1080 and VGA
(SD) cameras. It is important to note that some high resolution and high frame rate cameras may
demand faster headend processing ability, such as a PC graphics card to present a quality image.
If the headend processing equipment is insufficient in speed, the image may show pixilation and
latency. It is advisable to pretest system if unsure. Alternatively, frame rate and resolution may
be reduced to accommodate system equipment.
Technical Specifications:
Parameter
Description
Connections
BNC for Coax link. RJ45 for extended Ethernet link.
Input power
requirements
Midspan or endspan port connected. PoE compliant to IEEE 802.3af (15W)
and PoE+ compliant to IEEE 802.3at (30W).
Indicators
Yellow (RJ45 connector): On - Link, Off - No Link, Blinking - Activity.
Green (RJ45 connector): On - 100Base-TX, Off - 10Base-T.
Yellow: PoE Active.
Environmental
Conditions
Operating Ambient Temperature: UL60950-1
eBridge100RM: --- 4ºF to 120.2ºF (-- 20ºC to +49ºC).
eBridge100TM: --- 4ºF to 120.2ºF (-- 20ºC to +49ºC).
eBridge100ST: For 15W: -- 40ºF to 167ºF (--- 40ºC to 75ºC).
For 30W: -- 40ºF to 140ºF (--- 40ºC to 60ºC).
Relative humidity: 85%, +/ --- 5%
Storage Temperature: -- 4º to 158ºF (--- 20º to 70ºC.
Operating Altitude: -- 1000 to 6,561.679 ft. (-- 304.8 to 2000m).
Regulatory
Compliance
UL/CUL Listed for Information Technology Equipment (UL 60950-1).
CE approved. C-Tick compliant.
Weights (approx.) Product: 3.88 oz. (0.11 kg), Shipping: 6.70 oz. (0.19 kg).
