10
• This equipment is heavy and must not be lifted single-handedly, either
GET HELP
or use suitable lifting equipment.
• Cordon off the work area and keep members of the public and unauthorized personnel at a safe distance.
• Personal Protective Equipment (PPE) must be worn by the operator whenever this equipment is being used (see Health & Safety).
• Make sure you know how to safely switch this machine
OFF
before you switch it
ON
in case you get into dif
¿
culty.
• Always switch OFF and un-plug the motor before transporting, moving it around the site or servicing it.
• During use the motor becomes very hot, allow the motor to cool before touching it. Never leave the motor running and unattended.
• Never remove or tamper with any guards
¿
tted, they are there for your protection. Always check guards for condition and
security, if any are damaged or missing,
DO NOT USE THE MACHINE
until the guard has been replaced or repaired.
• Never pull or guide the machine using the cable and never pull on the cable to diconnect the plug.
•
DO NOT
operate the
MACHINE
when you are ill, feeling tired, or when under the in
À
uence of alcohol or drugs.
• Ensure that any trailing cable is protected against damage and not liable to be tripped over or trapped underneath the machine.
•
DO NOT
use the Motor Guard as a Lifting Point.
•
DO NOT
Jet Wash the machine as this could result in serious injury or even death!
•
DO NOT
use this machine in wet conditions. The electrical components of the machine
MUST NEVER
be exposed to water or
liquid of any kind as this could result in serious injury or even death!
•
Belle strongly recommends the use of a Residual Current Device on 220/240v electrics.
Fire Fighting
If your machine catches
¿
re, turn off the electric supply. Using a dry powder or C02
¿
re extinguisher put out the
¿
re. If the
¿
re can not
be put out, keep away and call the
¿
re brigade. If you are in any doubt about the safety condition of your machine, please consult your
nearest Altrad Belle dealer or Altrad Belle direct.
Electric Motors
All portable electric appliances are dangerous if abused. This machine will only operate on one voltage. Check the power supply to
ensure it corresponds to the voltage as stamped on the motor. Make sure that the motor is switched off before you plug it into the
power supply.
220/240v -
Always use a Residual Current Device (“RCD”), (earth leakage trip), plugged directly into the 220/240v socket.
If using an extension cable, plug it directly into the RCD.
110v -
When using a portable transformer it must have a minimum output of 3.3kw and be continuously rated.
The symbols on the ON/OFF switch are 0=OFF and I=ON in accordance with international standards.
Safety Instructions
GB
For your own personal protection and for the safety of those around you, please read and ensure you fully understand the following
safety information. It is the responsibility of the operator to ensure that he/she fully understands how to operate this equipment safely.
If you are unsure about the safe and correct use of the ‘PCLX 12/40E’ Plate compactor, consult your supervisor or Altrad Belle.
Improper maintenance can be hazardous. Read and Understand this section before you perform any
maintenance, service or repairs.
CAUTION
DO NOT use an extension cable between the transformer and the power supply. Always ensure that
the cable between the 110v machine and transformer is a minium length of 3 metres. Ensure cable is
¿
tted with cable clip to the operating handle at all times.
WARNING
Plugs
The PCLX 12/40E Plate Compactor is intended for DIY or site usage, the following plug types are supplied
¿
tted to the product:-
110v Motor -
16 amp rated BS4343 plug type.
230v Motor
- 13 amp rated 3-pin BS1363 plug type
or 3-pin CEE7/7 Euro plug type.
Fitting a plug -
WARNING THIS PRODUCT MUST BE EARTHED
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code:
GREEN / YELLOW = EARTH, BLUE = NEUTRAL, BROWN = LIVE
The wire which is coloured Green and Yellow must be connected to the terminal in the plug marked E or coloured Green and Yellow.
The wire which is coloured Brown must be connected to the terminal in the plug marked L or coloured Red. The wire which is
coloured Blue must be connected to the terminal in the plug marked N or coloured Black.
Always ensure before connecting to the supply that the supply voltage is the same as the rated voltage marked on the motor
Extension Cables
If you need to use an extension cable it must be no longer than 25 metres (82 feet) in length. The wire section must be 2.5mm
2
on 230v
and 2.5mm
2
on 110v. Ensure that the extension cable is carefully laid out avoiding liquids, sharp edges and places where
vehicles might run over it. Avoid allowing the extension cable to be trapped underneath the plate compactor. Unroll it fully or it will over-
heat and could catch
¿
re. Make sure that any extension cable connections are dry and safe.
NVR - No Volt Release
The motors which are
¿
tted to the machine are
¿
tted with a NVR (No Volt Release) Switch. This mean that if the power fails, the motor
will not automatically restart when the power is restored. The machine will need to be manually restarted.
