background image

with the performance of this product.

 

 

 

Use the product only with the supplied power supply cord set. If you need to 
replace the power cord set, make sure that the new power cord meets the following 
requirements: detachable type, UL listed/CSA certified, VDE approved or its 
equivalent, 4.6 meters (15 feet) maximum length.

 

 

Product servicing

 

Do not attempt to service this product yourself, as opening or removing covers may 
expose you to dangerous voltage points or other risks. Refer all servicing to qualified 
service personnel.

 

Unplug this product from the wall outlet and refer servicing to qualified service 
personnel when:

 

 

 

the power cord or plug is damaged, cut or frayed

 

 

liquid was spilled into the product

 

 

the product was exposed to rain or water

 

 

the product has been dropped or the case has been damaged

 

 

the product exhibits a distinct change in performance, indicating a need for service

 

 

the product does not operate normally after following the operating instructions

 

 

 

Notes

Adjust only those controls that are covered 

 

by the operating instructions, since improper 

 

adjustment of other controls may result in damage 

 

and will often require extensive work by a qualified 

 

technician to restore the product to normal condition.

 

 

This server should be located in a restricted access 

 

location or an area with similar instruction.

 

 

Caution:

 Danger of explosion if battery is 

 

incorrectly replaced. Replace only with the same or 

 

equivalent type recommended by the manufacturer. 

 

Dispose of used batteries according to the 

 

manufacturer's instructions.

 

 

Disposal instructions

 

Summary of Contents for Altos BrainSphere R365 F5





























Reviews: