manualshive.com logo in svg

Altera Stratix V Hard IP, User Manual

The Altera Stratix V Hard IP user manual is available for free download on our website. This comprehensive manual provides detailed instructions and information on effectively utilizing the product's features and functionalities. Enhance your understanding and optimize your experience with our cutting-edge technology by referring to the user manual available at manualshive.com.

Share
Download
background image

Chapter 6: IP Core Interfaces

6–45

Hard IP Reconfiguration Interface

June 2012

Altera Corporation

Stratix V Hard IP for PCI Express

User Guide

Table 6–21

 describes the Hard IP reconfiguration signals. 

Figure 6–37

 shows the timing of writes and reads on the Hard IP reconfiguration bus. 

f

For a detailed description of the Avalon-MM protocol, refer to the 

Avalon 

Memory-Mapped Interfaces

 chapter in the 

Avalon Interface Specifications

.

Table 6–20. Hard IP Reconfiguration Signals 

Signal

I/O

Description

hip_reconfig_clk

I

Reconfiguration clock. The frequency range for this clock is 50–125 MHz.

hip_reconfig_rst_n

I

Active-low Avalon-MM reset. Resets all of the dynamic reconfiguration 
registers to their default values as described in 

Table 14–1 on page 14–1

.

hip_reconfig_address[9:0]

I

The 10-bit reconfiguration address.

hip_reconfig_read

I

Read signal. This interface is not pipelined. You must wait for the return of 
the 

hip_reconfig_readdata[15:0]

 from the current read before 

starting another read operation. 

hip_reconfig_readdata[15:0]

O

16-bit read data. 

hip_reconfig_readdata[15:0]

 is valid on the third 

cycle after the assertion of 

hip_reconfig_read

.

hip_reconfig_write

I

Write signal.

hip_reconfig_writedata[15:0]

I

16-bit write model.

hip_reconfig_byte_en[1:0]

I

Byte enables, currently unused.

ser_shift_load

I

You must toggle this signal once after changing to user mode before the 
first access to read-only registers. This signal should remain asserted for 
a minimum of 324 ns after switching to user mode. 

interface_sel

I

A selector which must be asserted when performing dynamic 
reconfiguration. Drive this signal low 4 clock cycles after the release of 

ser_shift_load

. 

Figure 6–37. Hard IP Reconfiguration Bus Timing of Read-Only Registers

avmm_clk

user_mode

ser_shift_load

interface_sel

avmm_wr

avmm_wrdata[15:0]

avmm_rd

avmm_rdata[15:0]

D0

D0

D1

D1

D2 D3

324 ns

4  clks

4  clks

3 clks

Summary of Contents for Stratix V Hard IP









































































































































































































































Reviews:

No comments

Related manuals for Stratix V Hard IP

fadini Elpro S20 Instructions Manual preview
Elpro S20
Brand: fadini Pages: 32
ICP WAFER-5823 User Manual preview
WAFER-5823
Brand: ICP Pages: 50
ST ST9 EPB User Manual preview
ST9 EPB
Brand: ST Pages: 24
NXP Semiconductors MPT612 User Manual preview
MPT612
Brand: NXP Semiconductors Pages: 269
Biostar M7 VIF Test Report preview
M7 VIF
Brand: Biostar Pages: 72
Gigabyte GA-Z170-HD3P User Manual preview
GA-Z170-HD3P
Brand: Gigabyte Pages: 44
JETWAY BA-500PRO User Manual preview
BA-500PRO
Brand: JETWAY Pages: 58
ASROCK N68-GE Installation Manual preview
N68-GE
Brand: ASROCK Pages: 83
OLIMEX ADuC-MT7020 User Manual preview
ADuC-MT7020
Brand: OLIMEX Pages: 13
SmartOne 74.226 Quick Start Manual preview
74.226
Brand: SmartOne Pages: 2
Texas Instruments ADS8472EVM User Manual preview
ADS8472EVM
Brand: Texas Instruments Pages: 20
Aaeon GENE-5315 User Manual preview
GENE-5315
Brand: Aaeon Pages: 74
Sleipner SX35 Installation Manual preview
SX35
Brand: Sleipner Pages: 24
ASROCK PHANTOM GAMING B650E PG-ITX WiFi User Manual preview
PHANTOM GAMING B650E PG-ITX WiFi
Brand: ASROCK Pages: 62
Hochiki TCH-B100 Manual preview
TCH-B100
Brand: Hochiki Pages: 8
SOYO SY-P4RC350 User Manual preview
SY-P4RC350
Brand: SOYO Pages: 29
Analog Devices EVAL-AD7175-8SDZ User Manual preview
EVAL-AD7175-8SDZ
Brand: Analog Devices Pages: 11
Analog Devices EVAL-AD5934EB Preliminary Technical Data preview
EVAL-AD5934EB
Brand: Analog Devices Pages: 32

Brands by name

Popular brands

Load more brands