1
TM
Effective: August 1999
HAND-HELD DEVICE
PROGRAMMER
For SmartOne Devices
74.226
DESCRIPTION
The Hand-Held Device Programmer (the programmer) provides
the system installer/service person with a convenient means to
assign device address information and test device operation. The
programmer is designed to support all SmartOne intelligent/ad-
dressable devices. A table of supported devices is provided on the
other side of this instruction sheet.
NOTE:
Prior to using the programmer, you need to ensure that
you have the supplied accessories, listed in the table be-
low.
.
o
N
t
r
a
P
n
o
i
t
p
i
r
c
s
e
D
1
0
0
-
3
1
0
0
0
2
-
4
7
)
t
i
n
u
e
t
e
l
p
m
o
c
(
r
e
m
m
a
r
g
o
r
P
e
c
i
v
e
D
1
0
0
-
9
9
9
7
1
1
-
6
0
*
k
c
a
P
r
e
w
o
P
C
D
/
C
A
1
0
0
-
3
0
0
8
1
1
-
6
0
*
d
r
o
C
C
A
1
0
0
-
8
9
9
7
1
1
-
6
0
*
)
e
c
i
v
e
d
n
i
d
e
ll
a
t
s
n
i
(
k
c
a
P
y
r
e
t
t
a
B
1
0
0
-
3
1
0
0
0
2
-
4
7
N
/
P
l
e
v
e
l
p
o
t
n
i
d
e
il
p
p
u
s
ll
A
*
PREPARING FOR OPERATION
Prepare the programmer for operation with AC adapter as follows
1. Connect device interface cable to the PC line connector on
the top of the programmer.
2. Connect the small plug of the power pack to the DC input
connector on the top of the programmer and then plug the line
cord into a 115 VAC, 60 Hz outlet.
3. Verify that the green DC Input LED is lit. The yellow Bat.
Charger LED will also light if the batteries are not fully charged.
4. Set the power switch to the ON position (up direction).
5. Verify that the green Power On LED is lit and that the display
is flashing each segment of the six characters.
6. After 30 seconds ensure the top row of the display is flashing.
The bottom row of the display should be blank.
PREPARING FOR OPERATION
WITH INTERNAL BATTERIES
1. Connect Interface Cable to the PC line connector on the top of
the programmer.
2. Set the power switch to the ON position (up direction).
3. Verify that the green Power On LED is lit and that the display
is flashing each segment of the six characters.
4. If the Bat. Failure LED is lit or no LEDs are lit, charge the
batteries according to procedure.
BATTERY CHARGING
If the Bat. Failure LED lights on the programmer, go to AC opera-
tion or charge the batteries as described below:
1. Ensure that the power switch is in the off position (down direc-
tion).
2. Connect the small plug of the power pack to the DC IN con-
nector on the top of the Programmer and then plug the line
cord into a 115 VAC, 60 Hz outlet.
3. Verify that the DC Input and Bat. Charger LEDs are lit.
4. Charge batteries for at least 1 hour. If the Bat. Failure LED is
illuminated after the charge. Replace the Programmers bat-
teries.
TO CHANGE OR SET
THE ADDRESS OF A DEVICE
1. Connect the alligator clips of the interface cable to the termi-
nals of an addressable device.
2. After about 17 seconds, the top row of the display should indi-
cate the device address (000 to 255), and shortly after, the
bottom row of the display should indicate ooo.
NOTE:
All new addressable devices should have an address of
zero.
3. If the Programmer Trouble Code LED lights, or if the Pro-
grammer beeps or if a trouble code is displayed, replace the
device with an operational device and repeat step 2. If trouble
indications persist, go to troubleshooting section.
4. To change the address, enter a value between 001 and 255
into the key pad. The selected value will appear in the bottom
row of the display. Press the <enter> key.
