Analog Devices AD9361 Reference Manual Download

Page: 1 / 128

AD9361 Reference Manual

UG-570

One

Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com

AD9361

Reference Manual

PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.

| Page 1 of 128

GENERAL INFORMATION

Complete specifications for the

AD9361

part can be found in the

AD9361

data sheet, which is available from Analog Devices, Inc., and

should be consulted in conjunction with this user guide when using the evaluation board.
Additional information about the

AD9361

registers can be found in the

AD9361 Register Map Reference Manual

. While the register map

is provided as a convince and informational for those who want to understand the low level operation of the part, it is not recommended
to attempt to create your own software. Analog Devices provides complete drivers for the

AD9361

for both bare metal/No-OS and

operating systems (Linux). The

AD9361

and

AD9364

share the same API. The

AD9361

and

AD9364

drivers can be found at:

•

Linux

wiki page

•

No-OS

wiki page

Support for these drivers can be found at:

•

Linux

engineer zone page

•

No-OS

engineer zone page

Rev. A

Summary of Contents for AD9361

































































































































Search results

Summary of Contents for AD9361

Reviews:

Related manuals for AD9361

Brands by name

Popular brands

Analog Devices AD9361, Reference Manual

Search results

Summary of Contents for AD9361

Reviews:

Related manuals for AD9361

Brands by name

Popular brands