Altera EP2AGX125 Device Handbook Download Page 3 | Manualshive

Page: 3 / 144

background image

Arria II Device Handbook Volume 1: Device Interfaces and Integration
December 2010

AIIGX51001-4.0

© 2010 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat. & Tm. Off.

and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective holders as described at

www.altera.com/common/legal.html

. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera’s standard warranty, but

reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any

information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device

specifications before relying on any published information and before placing orders for products or services.

1. Overview for the Arria II Device Family

The Arria

®

II device family is designed specifically for ease-of-use. The

cost-optimized, 40-nm device family architecture features a low-power,
programmable logic engine and streamlined transceivers and I/Os. Common
interfaces, such as the Physical Interface for PCI Express

®

(PIPE) (PCIe

®

), Ethernet,

and DDR3 memory are easily implemented in your design with the Quartus

®

II

software, the SOPC Builder design software, and a broad library of hard and soft
intellectual property (IP) solutions from Altera

®

. The Arria II device family makes

designing for applications requiring transceivers operating at up to 6.375 Gbps fast
and easy.

This chapter contains the following sections:

■

“Arria II Device Feature” on page 1–1

■

“Arria II Device Architecture” on page 1–6

■

“Reference and Ordering Information” on page 1–14

Arria II Device Feature

The Arria II device features consist of the following highlights:

■

40-nm, low-power FPGA engine

■

Adaptive logic module (ALM) offers the highest logic efficiency in the industry

■

Eight-input fracturable look-up table (LUT)

■

Memory logic array blocks (MLABs) for efficient implementation of small
FIFOs

■

High-performance digital signal processing (DSP) blocks up to 550 MHz

■

Configurable as 9 × 9-bit, 12 × 12-bit, 18 × 18-bit, and 36 × 36-bit full-precision
multipliers as well as 18 × 36-bit high-precision multiplier

■

Hardcoded adders, subtractors, accumulators, and summation functions

■

Fully-integrated design flow with the MATLAB and DSP Builder software
from Altera

December 2010
AIIGX51001-4.0

«
1
2
3
4
5
...
»

Summary of Contents for EP2AGX125

















































































































































Reviews:

No comments

Related manuals for EP2AGX125

Brand: ECS Pages: 56

Brand: Intel Pages: 97

Brand: Gigabyte Pages: 17

Brand: Gigabyte Pages: 40

ECM-5716 Series

Brand: Aaeon Pages: 131

Brand: Advantech Pages: 124

Brand: Linear Pages: 16

Brand: DFI Pages: 48

Brand: Apex Digital Pages: 5

Brand: Gigabyte Pages: 74

Brand: Supermicro Pages: 126

Brand: Norco Pages: 60

BOOSTXL-DRV8301

Brand: Texas Instruments Pages: 13

SBC86620 Series

Brand: AXIOMTEK Pages: 90

Brand: DFI Pages: 48

Brand: TYAN Pages: 47

Brand: Suzuki Pages: 3

Brand: ADLINK Technology Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands