manualshive.com logo in svg

Altera Cyclone V GX FPGA, Reference Manual, Page: 36 / 60

Share
Download
Altera Cyclone V GX FPGA Reference Manual Download Page 36

2–28

Chapter 2: Board Components

Components and Interfaces

Cyclone V GX FPGA Development Board

May 2013

Altera Corporation

Reference Manual

The HSMC connector has a total of 172 pins, including 120 signal pins, 39 power pins, 
and 13 ground pins. The ground pins are located between the two rows of signal and 
power pins, acting both as a shield and a reference. The HSMC host connector is 
based on the 0.5 mm-pitch QSH/QTH family of high-speed, board-to-board 
connectors from Samtec. There are three banks in this connector. Bank 1 has every 
third pin removed as done in the QSH-DP/QTH-DP series. Bank 2 and bank 3 have 
all the pins populated as done in the QSH/QTH series. 

Figure 2–8

 shows the bank arrangement of signals with respect to the Samtec 

connector's three banks.

The HSMC interface has programmable bi-directional I/O pins that can be used as 
2.5-V LVCMOS, which is 3.3-V LVTTL-compatible. These pins can also be used as 
various differential I/O standards including, but not limited to, LVDS, mini-LVDS, 
and RSDS with up to 17 full-duplex channels.

1

As noted in the 

High Speed Mezzanine Card (HSMC) Specification

 manual, LVDS and 

single-ended I/O standards are only guaranteed to function when mixed according to 
either the generic single-ended pin-out or generic differential pin-out.

Table 2–24

 lists the HSMC interface pin assignments, signal names, and functions.

Figure 2–8. HSMC Signal and Bank Diagram

Bank 3 

Power 

D(79.40) 

-or- 

LVDS 

CLKIN2, CLKOUT2 

Bank 2 

Power 

D(39:0) 

-or- 

D[3:0] + LVDS 

CLKIN1, CLKOUT1 

Bank 1

8 TX Channels CDR

8 RX Channels CDR

JTAG

SMB

CLKIN0, CLKOUT0

Table 2–24. HSMC Interface Pin Assignments, Schematic Signal Names, and Functions (Part 1 of 4)

Board 

Reference (J1)

Schematic Signal Name

Cyclone V GX

Pin Number

I/O Standard

Description

17

HSMA_TX_P3

K4

1.5-V PCML

Transceiver TX bit 3

18

HSMA_RX_P3

L2

1.5-V PCML

Transceiver RX bit 3

19

HSMA_TX_N3

K3

1.5-V PCML

Transceiver TX bit 3n

20

HSMA_RX_N3

L1

1.5-V PCML

Transceiver RX bit 3n

21

HSMA_TX_P2

M4

1.5-V PCML

Transceiver TX bit 2

22

HSMA_RX_P2

N2

1.5-V PCML

Transceiver RX bit 2

23

HSMA_TX_N2

M3

1.5-V PCML

Transceiver TX bit 2n

24

HSMA_RX_N2

N1

1.5-V PCML

Transceiver RX bit 2n

Summary of Contents for Cyclone V GX FPGA





























































Reviews:

No comments