manualshive.com logo in svg

Altera Cyclone V GX FPGA, Reference Manual, Page: 32 / 60

Share
Download
Altera Cyclone V GX FPGA Reference Manual Download Page 32

2–24

Chapter 2: Board Components

Components and Interfaces

Cyclone V GX FPGA Development Board

May 2013

Altera Corporation

Reference Manual

Components and Interfaces

This section describes the development board's communication ports and interface 
cards relative to the Cyclone V GX device. The development board supports the 
following communication ports:

■

PCI Express

■

10/100/1000 Ethernet

■

HSMC

■

SDI video output/input

PCI Express

The Cyclone V GX FPGA development board is designed to fit entirely into a PC 
motherboard with a ×4 PCI Express slot that can accommodate a full height long form 
factor add-in card. This interface uses the Cyclone V GX's PCI Express hard IP block, 
saving logic resources for the user logic application. The PCI express edge connector 
has a presence detect feature to allow the motherboard to determine if a card is 
installed.

f

For more information on using the PCI Express hard IP block, refer to the 

PCI Express 

Compiler User Guide

.

The PCI Express interface supports auto-negotiating channel width from ×1 to ×4 by 
using Altera's PCIe MegaCore IP. You can also configure this board to a ×1 or ×4 
interface through a DIP switch that connects the 

PRSNTn

 pins for each bus width. 

The PCI Express interface has a connection speed of 2.5 Gbps/lane for a maximum of 
20 Gbps full-duplex (Gen1).

The power for the board can be sourced entirely from the PCI Express edge connector 
when installed into a PC motherboard. Although the board can also be powered by a 
laptop power supply for use on a lab bench, Altera recommends that you do not 
power up from both supplies at the same time. Ideal diode power sharing devices 
have been designed into this board to prevent damages or back-current from one 
supply to the other.

The 

PCIE_REFCLK_P/N

 signal is a 100 MHz differential input that is driven from the PC 

motherboard on to this board through the edge connector. This signal connects 
directly to a Cyclone V GX 

REFCLK

 input pin pair using DC coupling. This clock is 

terminated on the motherboard and therefore, no on-board termination is required. 
This clock can have spread-spectrum properties that change its period between 
9.847 ps to 10.203 ps. The I/O standard is High-Speed Current Steering Logic (HCSL). 

Summary of Contents for Cyclone V GX FPGA





























































Reviews:

No comments