Altera Cyclone V GX FPGA Page 21 Reference Manual Download | Manualshive

Page: 21 / 60

background image

Chapter 2: Board Components

2–13

FPGA Configuration

May 2013

Altera Corporation

Cyclone V GX FPGA Development Board

Reference Manual

FPGA Programming from Flash Memory

Flash memory programming is possible through a variety of methods. The default
method is to use the factory design—Board Update Portal. This design is an
embedded webserver, which serves the Board Update Portal web page. The web page
allows you to select new FPGA designs including hardware, software, or both in an
industry-standard S-Record File (

.flash

) and write the design to the user hardware

page (page 1) of the flash memory over the network.

The secondary method is to use the pre-built parallel flash loader (PFL) design
included in the development kit. The development board implements the Altera PFL
megafunction for flash memory programming. The PFL megafunction is a block of
logic that is programmed into an Altera programmable logic device (FPGA or CPLD).
The PFL functions as a utility for writing to a compatible flash memory device. This
pre-built design contains the PFL megafunction that allows you to write either page 0,
page 1, or other areas of flash memory over the USB interface using the Quartus II
software. This method is used to restore the development board to its factory default
settings.

Other methods to program the flash memory can be used as well, including the
Nios

®

II processor.

f

For more information on the Nios II processor, refer to the

Nios II Processor

page of

the Altera website.

On either power-up or by pressing the program configuration push button,

PGM_CONFIG

(S6), the MAX V CPLD 5M2210 System Controller's PFL configures the

FPGA from the flash memory. The PFL megafunction reads 16-bit data from the flash
memory and converts it to fast passive parallel (FPP) format. This 16-bit data is then
written to the dedicated configuration pins in the FPGA during configuration.

Pressing the

PGM_CONFIG

push button (S6) loads the FPGA with a hardware page

based on which

PGM_LED[2:0]

(D11, D12, D13) illuminates.

Table 2–6

defines the

design that loads when you press the

PGM_CONFIG

push button.

B7

FX2_WAKEUP

—

3.3-V

USB 2.0 PHY wake signal

G2

USB_CLK

AA23

3.3-V

USB 2.0 PHY 48-MHz interface clock

Table 2–5. USB 2.0 PHY Schematic Signal Names and Functions (Part 2 of 2)

Board Reference

(U16)

Schematic

Signal Name

Cyclone V GX

Pin Number

I/O Standard

Description

Table 2–6. PGM_LED Settings

(1)

PGM_LED0 (D12)

PGM_LED1 (D13)

PGM_LED2 (D14)

Design

ON

OFF

OFF

Factory hardware

OFF

ON

OFF

User hardware 1

OFF

OFF

ON

User hardware 2

Note to

Table 2–6

:

(1) ON indicates a setting of ’0’ while OFF indicates a setting of ’1’.

«
...
19
20
21
22
23
...
»

Summary of Contents for Cyclone V GX FPGA





























































Reviews:

No comments

Related manuals for Cyclone V GX FPGA

Brand: UniKey Pages: 20

Brand: YOKOGAWA Pages: 150

Brand: Jetter Pages: 24

Brand: Festo Pages: 109

Brand: Topworx Pages: 8

Ambience Control 1

Brand: EuroLite Pages: 20

Brand: SKF Pages: 88

by-me Eikon 20526

Brand: Vimar Pages: 6

SYSVRF AHU 10HP S

Brand: SystemAir Pages: 16

Brand: Zapi Pages: 30

Brand: FuzzDog Pages: 9

DMC-40x0 Series

Brand: Galil Motion Control Pages: 280

ELEMENTAIR B-MARK I

Brand: Xvent Pages: 9

Kade KZ-700-U/H

Brand: ATT Holding Pages: 12

Brand: Casambi Pages: 4

Brand: Vector Pages: 22

Brand: KEPCO Pages: 34

DMX-LED-DIMMER X9 HR

Brand: DMX4ALL Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands