ALTER GM 140 Manual Download Page 7

    

GM 140 

   page    6  

of 12

                                                                                                                                  File: GM140_r0eng -  October 2003   -    Technical note: GM 140

    

GM 140 

   File: GM140_r0eng -  October 2003 - Technical note: GM 140                                                                                                                              

         

page     7  

of  12 

0 1

3

45

67

8

9

2

0 1 2

3

45

67

8

9

t

on

FREQ

0 2

3

45

67

8

9

1

0 1 2

3

45

67

8

9

t

on

FREQ

0 1 2

3

45

67

8

9

0 2

3

45

67

8

9

1

t

on

FREQ

0 1 2

3

45

67

8

9

0 1

3

45

67

8

9

2

t

on

FREQ

0 1 2

3

45

67

8

9

0 1 2

3

56

7

8

9

4

t

on

FREQ

Microwaves emission mode selection

You can select two different modes of microwaves 

emission: continuous or pulsed mode.

In pulsed mode you can drive pulses by:

- an external signal generator or
- FREQ and 

t

on

 switches on front panel added with two 

analog signals (internal generator).

Continuous:

Pin 5

CONN#3

CW/PULSE MODE

OFF

Pulsed, with external generator 

Pin 5

CONN#3

CW/PULSE MODE

ON

Pin 9-10

CONN#3

PULSE PATTERN

PWM: Amplitude 24 Vdc

t

on

=0.1÷10ms

t

off

=1÷100ms

Max Duty Cycle=20% 

(with hysteresis)

Pulsed, with internal generator

Pin 5

CONN#3

CW/PULSE MODE

ON

Pin 9-21

CONN#3

Pins connected (shortcircuited)

Pin 7-8

CONN#3

SET VALUE FOR FREQUENCY

See table below

0÷10Vdc / 9÷310Hz

Select FREQ=2

0÷10Vdc / 230÷4500Hz

Select FREQ=1

 

Pin 20-8

CONN#3

SET VALUE FOR 

t

on

See table below

0÷10Vdc / 60÷300

µ

S

Select 

t

on

=1

0÷10Vdc / 220

µ

S÷1.6mS

Select 

t

on

=2

0÷10Vdc / 1.2÷9.5mS

Select

 t

on

=4

           Frequency selection: 0÷10Vdc PIN 7, 8

 

 

Frequency: 9Hz÷310Hz

 

 

 

Frequency: 230Hz÷4500Hz

 

Different selection not allowed

           Time selection: 0÷10Vdc PIN 20, 8

 

 

Time: 60µs÷300µs

 

 

 

Time: 220µs÷1,6ms

 

 

 

Time: 1,2ms÷9,5ms

 

Different selection not allowed

Summary of Contents for GM 140














Reviews: