17
16
EN
RESETTING TO FACTORY SETTINGS
1. Pull out the mains plug
2. Simultaneously press and hold down the first three buttons (1, 2
and 3) on the control panel
3. Plug in the mains plug and continue to hold down the same
three buttons
4. After about 5 seconds, all buttons will flash for about 3 seconds
as confirmation and the buttons can be released
5. Factory settings restored
The following settings are reset to the factory settings:
– All user settings
– All HCL curves
– All radio buttons (any pre-sets may be deleted)
– All switching times
– All network settings
– User password will be reset to «1234»
Button
status
Action
Description
Button follow-up
status
Light follow-up
status
Dimming the light field
or
1
3
4
or
Press the button
for the correspon-
ding channel (1,
3 or 4) until the
desired dimming
level is reached.
Every time the but-
ton is released, the
dimming direction
is reversed.
The corresponding
button lights up
orange.
The corresponding
light field is in «manual
control» and is no
longer controlled by the
automatic system.***
***Note: If only one direct light field is temporarily overridden in the case of the PLATO floor luminaire, the other
remains in automatic mode – this is indicated by button 2 which is additionally illuminated in white. When both direct
light fields are in «manual control», the entire light switches to «manual control» – the white LED in button 2 is OFF.
With the ECO S floor luminaire, the light field which has not been overridden remains at the same dimming level it
was in before the action was taken. The light switches completely to «manual control mode».
Adjusting the colour temperature
(Optional function)
2
Press button 2
until the desired
colour temperature
is reached. Each
further press of the
button changes
the direction in
which the colour
temperature is
regulated (from
cold to warm or
vice versa).
The LED display of
button 2 is off.
The light is in «manual
control» of the colour
temperature control.
This means that the
colour temperature
remains permanently
at the set value and no
longer follows the defi-
ned colour temperature
curve.****
****Note: As the default setting, manual adjustment of the colour temperature is only possible with direct light. The
indirect light follows the defined colour temperature curve even when the colour temperature is manually overridden.
This should prevent different colour temperatures from being visible on the ceiling within a room.
WEBLINK
Operating instructions, assembly instruc-
tions, FAQs and link to app for wireless
light control and expanded configurati-
ons.
ENHANCED OPERATION
These functions allow users to temporarily override individual light fields. This means that if a specific lighting situa-
tion is to be temporarily adjusted, the individual light fields can be switched on or off individually or dimmed to the
desired brightness.
Button
status
Action
Description
Button follow-up
status
Light follow-up
status
Switching off the light field
1
3
4
or
or
Briefly press the
button for the
corresponding
channel (1, 3 or 4) .
The corresponding
button lights up
orange.
The corresponding
light field is in «manual
control» and is no
longer controlled by the
automatic system.*
*Note: If only one direct light field is temporarily overridden in the case of the PLATO floor luminaire, the other
remains in automatic mode – this is indicated by button 2 which is additionally illuminated in white. When both direct
light fields are in «manual control», the entire light switches to «manual control» – the white LED in button 2 is OFF.
With the ECO S floor luminaire, the light field which has not been overridden remains at the same dimming level it
was in before the action was taken. The light switches completely to «manual control mode».
Switching on the light field
1
3
4
or
or
– Button 2 «bre-
athes»
– Briefly press the
button for the
corresponding
channel (1, 3
or 4)
The corresponding
button «breathes»
orange.
The corresponding
light field is in «manual
control reverse mode»
and is no longer con-
trolled by the automatic
system.**
**Note: If only one direct light field is temporarily overridden, the other remains in automatic mode – this is indicated
by button 2 which is additionally illuminated in white. When both direct light fields are in «manual control», the entire
light switches to «manual control» – the white LED in button 2 is OFF.
PROGRAMMING THE SWITCH-OFF TIME FOR THE MOTION DETECTOR
Action
Description
Control panel status
CAUTION: Switch-off time programming cannot be exited without saving a value. Any user-specific adjustments are
overwritten.
Step 1
5 sec.
2
+
1
Press and hold down buttons 1 and
2 together for 5 seconds.
Buttons 1-3 flash. The button which
corresponds to the currently-set
switch-off time is constantly lit.*
*Note: If the switch-off time has been configured for the user in the app, none of the buttons will remain constant-
ly lit.
Step 2
or
1
2
3
or
1 = Set to 30 minutes
2 = Set to 15 minutes
3 = Set to 5 minutes
**
While the setting is being saved,
button 2 flashes rapidly for approx. 3
seconds.
**Note: Any customer-specific settings are overwritten by the switch-off time programming.
EN
