Altai Technologies A8 Installation Manual Download Page 4

Page: 4 / 24

A8 Installation Guide_ R3 Hardware Platform

TPS13-010_rev1.0

Contents

1. Introduction ............................................................................................................................ 5

2. A8 Base Station Outlook ....................................................................................................... 5

3. A8 Antenna Outlook ............................................................................................................. 6

4. A8 Base Station Package .................................................................................................... 7

5. A8 Antenna Package ........................................................................................................... 7

6. Site Preparation...................................................................................................................... 9

7. Mounting A8 antenna on a pole ....................................................................................... 9

8. Mounting 5GHz Radio Antenna........................................................................................ 11

9. Mounting A8 Base Station on the Pole ............................................................................ 12

10.

Mounting A8 Base Station on the Wall ........................................................................ 12

11.

Connecting RF Cables ................................................................................................... 13

12.

Weatherproofing the RF Connectors .......................................................................... 15

12.1.

Introduction .......................................................................................................... 15

12.2.

Installation Tips ...................................................................................................... 16

12.3.

Preparing A8 BTS RF Ports ................................................................................... 17

12.4. Connecting RF Cables ........................................................................................... 18

12.5.

RF Cable-to-A8 BTS Connection ....................................................................... 18

12.6.

RF Cable-to-Antenna Connection ................................................................... 20

13.

Recommendation on RF cable and Antenna Pole ................................................. 21

13.1.

RF Cable ................................................................................................................ 21

13.2.

Antenna Pole Height and Size .......................................................................... 22

14.

Grounding Protection ..................................................................................................... 22

15.

Typical Site Setup ............................................................................................................. 23

Summary of Contents for A8






















Search results

Summary of Contents for A8

Reviews:

Related manuals for A8

Brands by name

Popular brands

Altai Technologies A8, Installation Manual

Search results

Summary of Contents for A8

Reviews:

Related manuals for A8

Brands by name

Popular brands