ALPINE HCE-C500 EN 68-18693Z84-A (A5)
3
-EN
ONS.
ny
used
s
es,
g
r
DER
EL
ment
N
al
hat
, gear
arts,
to
e or
em,
ard
x,
has
fire
t,
fire,
ED
ORE
O
ND
WHEN USING A DRILL TO MAKE A HOLE, TAKE
PRECAUTIONS SUCH AS WEARING GOGGLES SO
FRAGMENTS DO NOT GET INTO THE EYES.
Failure to do so may result in injury.
CAUTION
This symbol means important instructions.
Failure to heed them can result in injury or
material property damage.
HAVE THE WIRING AND INSTALLATION DONE BY
EXPERTS.
The wiring and installation of this unit requires special
technical skill and experience. To ensure safety, always
contact the dealer where you purchased this product to have
the work done.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like
the seat rails) or sharp or pointed edges. This will prevent
crimping and damage to the wiring.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM
SECURELY.
Be sure to use only the specified accessory parts. Use of other
than designated parts may damage this unit internally or may
not securely install the unit in place. This may cause parts to
become loose resulting in hazards or product failure.
CONNECT LEADS PROPERLY.
Be sure to connect the colour coded leads according to
the diagram. Incorrect connections may cause the unit
to malfunction or cause damage to the vehicle’s electrical
system.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to the
product. Return it to your authorized Alpine dealer or the
nearest Alpine Service Center for repairing.
EXCEPT FOR THE CAMERA, DO NOT ATTACH ANY PARTS
TO AREAS WHICH WILL GET WET, OR WHERE THERE IS A
LOT OF HUMIDITY OR DUST.
Failure to do so may result in fire or damage.
DO NOT ATTACH THE CAMERA TO FLUOROCARBON
RESIN FINISHED CAR BODIES OR GLASS.
Doing so reduces the strength of the camera’s mounting.This
could cause it to fall off and cause injury or
damage to the car’s body.
DO NOT ATTACH THE CAMERA TO ANY SURFACE WHERE
THE ENTIRE ADHESIVE SURFACE CANNOT BE APPLIED.
Doing so reduces the strength of the camera’s mounting.This
could cause it to fall off and cause injury or
damage to the car’s body.
NOTICE
About Care of Device
Do not assert any excess pressure to the camera or the
mounting, as this could cause the camera direction to shift,
or the camera mounting bracket to come off.
To prevent the camera lens, mounting and cords from
changing colour or shape, or from deteriorating, wipe with
a chemical-free, damp cloth.
Do not use an automatic car wash or high-pressure washer.
Doing so could cause the camera to come off, damage to
the device cord, or may allow water to enter the camera or
the inside of the car.
In some cases, to attach the device, a hole must be drilled
in the car body, requiring use of touch-up paint (retail
product) for rust-prevention, and should be prepared
beforehand.
Be sure to disconnect the cable from the (–) battery post
before installing your HCE-C500 series. This will reduce
any chance of damage to the unit in case of a short-circuit.
About Rear Camera
The rear camera is optimised for use in this system. as a
dedicated product, it should not be used in other systems.
Do not use mobile phones and wireless devices near the
camera.
Doing so may result in noise on the screen or malfunction.
It is recommended to use mobile phones or wireless devices
away from the camera.
About Camera Installation Location
Before installing, make sure there is a enough space to be
able to install the camera. If possible, install the camera
in the center of the bumper. If the camera is installed
off-center, the image may differ from the actual view.
Calibration is necessary.
Confirming the Display Function
To connect the unit, confirm that the monitor will require a
compatible RCA pin jack.
•
•
•
•
•
•
•
•
•
