42
-EN
01GB05IVE-W535ABT.fm
ALPINE IVE-W535ABT/IVE-W535EBT 68-21057Z56-A (EN)
Adjusting the Time Correction (Time
Correction)
[Time Correction]
is selected on the Sound setup menu in step 3. Refer
to “Sound Setup Operation” (page 39).
Before performing the following procedures, refer to “About Time
Correction” (page 43).
Setting item: Time Correction
1
Touch
[ms]
or
[cm]
to select mode for making
adjustments.
Each time you touch, the onscreen button and correction
mode changes.
ms: Adjust time.
cm: Adjust listening position and distance from each speaker.
2
Touch
[
]
or
[
]
for each speaker to adjust the
time or distance.
0.0msec to 9.9msec (0.1msec/step)
0.0cm to 336.6cm (3.4cm/step)
All speaker setting values are adjustable in the range of 20ms or
680cm.
3
To store the adjusted setting value, touch and hold
[Preset1]
,
[Preset2]
, or
[Preset3]
for at least 2
seconds.
•
Touch
[Flat]
to set all values to 0.0.
•
If the Rear Speaker setting is “Off,” the Rear Speaker setting cannot
be edited (Refer to page 39).
•
If the Subwoofer setting is “Off,” the Subwoofer setting cannot be
edited (Refer to page 39).
Calling the Time Correction Value
Calling the pre-set time correction value.
Touch
[Preset1]
,
[Preset2]
, or
[Preset3]
on the time
correction screen.
The setting stored in the Preset will be recalled.
Adjusting the Crossover Settings (X-
OVER)
[X-OVER]
is selected on the Sound setup menu in step 3. Refer to
“Sound Setup Operation” (page 39).
Before performing the following procedures, refer to “About the
Crossover” (page 45).
Setting item: X-OVER
1
Touch
[Channel]
to select the channel.
Each time you touch, the channel switches.
•
The channel being adjusted is displayed in red.
2
Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch
[
]
or
[
]
of “Freq.,” then select the cut-off
frequency.
Setting contents: 20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) /
100 / 125 / 160 / 200 Hz
Adjusting the Slope
Touch
[
]
or
[
]
of “Slope,” then adjust the HPF or LPF
slope.
Setting contents: 0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct
Adjusting the Level
Touch
[
]
or
[
]
of “Level,” then adjust the HPF or LPF
level.
Setting contents: -12 to 0 dB (Initial setting: 0)
3
Repeat steps 1 to 2 to make adjustment to the other
channels.
4
To store the adjusted setting value, touch and hold
[Preset1]
,
[Preset2]
, or
[Preset3]
for at least 2
seconds.
•
Touch
[Flat]
to initialise all values.
•
If the Rear Speaker setting is “Off,” the Rear Speaker setting cannot
be edited (Refer to page 39).
•
If the Subwoofer setting is “Off,” the Subwoofer setting cannot be
edited (Refer to page 39).
•
While adjusting the X-OVER you should consider the frequency
response of the connected speakers.
Correction mode
Front HPF
Rear HPF
Subw. LPF
01GB00IVE-W535ABT.book Page 42 Wednesday, July 25, 2012 5:22 PM
