background image

7

-EN

ALPINE HCE-C200R  68-09359Z09-A (EN)

Installation and
Connections

Mounting the Rear Camera
(HCE-C200R)

Preparation

1

Check accessory parts.

1

Rear camera (1m)

2

Power unit (ACC:2m,
GND:2m, Reverse In:6m,
Reverse out:2m)

Installing the Power Unit

1

Attach the Velcro fastener (hard side) 

!

 to

the bottom of the power unit 

2

.

2

Attach the Velcro fastener (soft side) 

!

 to the

floor, and secure the power unit 

2

.

• When attaching the Velcro fastener (hard side) 

!

 to the

floor carpet, do so without the Velcro fastener (soft side)

!

 attached.

• It is recommended to install the power unit on the rear of

the instrument panel, or under a seat.

Installing the Switch

1

Attach the switch 

#

 according to the

following illustration.

Attach the supplied switch adhesive sheet 

#

.

Peel off the seal paper, and apply it to the back of
the switch, then peel off the other seal paper and
install in the desired location. If necessary, secure
the cable with the supplied cord clamps 

%

.

• Before attaching the switch, wipe off any dust, oil, etc., on

the attaching surface with a suitable cleaning cloth (sold
separately).

• Attach the switch in a location where driving is not

hindered.

3

Camera mounting

4

Hex screw

x 2

5

Hexagonal wrench

6

RCA extension cable
(2m)

7

Waterproofing pad

8

Waterproofing pad
adhesive sheet

9

Cord clamp

!

Velcro fastener

x 5

"

Tapping screw

#

Switch (3m)

x 2

x 4

#

Switch adhesive sheet

$

Camera extension
cable (7m)

%

Cord clamp (Switch)

x 3

Velcro fastener (hard side)

Switch

Summary of Contents for HCE-C200F


















Reviews: