manualshive.com logo in svg

Alpha MED Scientific MED64-Entry, Manual

Share
Download
Alpha MED Scientific MED64-Entry Manual Download Page 6

 

 

4

 

 

 

 

 

  3.2. Considerations for the position of devices

 

 

  In order to ensure sufficient space for an experiment, place the PC on the MED64-Entry amplifier (not essential). Pay attention so 

as not to damage the housing of the MED64-Entry Amplifier with the legs of the PC. Place the display monitor next to the PC and 
the MED Connector in front of the monitor. Do not place the power adaptor or other electronic devices close to the connection 
terminal on the back of the amplifier.

 

 
 

 

 

 

 

 

Above is an image of the ideal positions of components. The user can perform an experiment smoothly when there 

is a sufficient space next to or at the back of the laboratory desk with a power strip on the floor. If no perfusion 
system is used, about 100 cm width is sufficient, otherwise a larger space is necessary.

 

 

  3.3. Power source

 

 

  Three power sources are necessary for the MED64-Entry Amplifier and the Data Acquisition PC System (the desktop PC and the 

display monitor), and one additional power source is necessary to use the MED Thermo connector when it is used. Connect all the 
cords to one power strip connected to a wall outlet with the ground terminal (do not use an outlet on the desktop rack because it 
is often not grounded properly). Do not connect devices that are not necessary for the MED64-Entry to the power strip or to the 
wall outlet to which the MED64-Entry and other components are connected. Place the power cable and the power adaptor at a 
distance from the amplifier, the MED Connector and the 68-pin SCSI cable.

 

 

 

 

 

Display monitor

 

PC

 

MED64-Entry 

Amplifier

 

Space for cables on the back of the amplifier

 

About 20 cm depth is necessary.

 

MED Connector

 

Mouse

 

Keyboard

 

PC

 

Display monitor

 

Power strip (on the floor)

 

Power adaptor (on the floor)

 

75 cm

 

120 cm

 

アンプ後面

 

Data acquisition device other 
than PCIe-6343 (not connected).

 

Save after assignment 
of the name.

 

Space for cables in front of the amplifier

 

About 15 cm depth is necessary.

 

Pump (when 

perfusing)

 

Water bath

 

(when perfusing)

 

MED64-Entry Amplifier

 

Summary of Contents for MED64-Entry






























Reviews:

No comments

Brands by name

Popular brands

Load more brands