Alpha ESS Storion-T100 Operation & Maintenance Manual Download Page 22

Page: 22 / 24

Fault Name

Troubleshooting

Fault

Category

BMS

LCD Fault

Display

Commu_fail_LMU

LMU

Communication

fault

Check if the communication cable

connector between the

HV-control box and the battery is

not plugged in.

If the problem is not resolved,

please contact AlphaESS customer

service.

Cell-Ov-Temp

Cell over

temperature fault

Stop charging and discharging and

then run the system after the fault

is eliminated.

If the problem is not resolved,

please contact AlphaESS customer

service.

Commu_fail_BMU

BMU

Communication

fault

Check if the communication cable

connector between the

HV-control box and the TOP

BMU is not plugged in.

If the problem is not resolved,

please contact AlphaESS

customer service.

TROUBLESHOOTING

Troubleshooting

Fault Name

Troubleshooting

Fault

Category

BMS

LCD Fault

Display

Cell-Temp-Diﬀ

Cell temperature

diﬀerent fault

Shut down the system for about

2 hours, then restart the system

to check if the fault is eliminated.

If the problem is not resolved,

please contact AlphaESS

customer service.

Chrg-Ov-Curr

Module charge

over current fault

Restart the system to check if the

fault is eliminated.

If the problem is not resolved,

stop any operation on the system

and contact AlphaESS customer

service.

Disch-Ov-Curr

Module discharge

over current fault

Restart the system, turn oﬀ some

of the loads to check if the fault

is eliminated.

If the problem is not resolved,

stop any operation on the system

and contact AlphaESS customer

service.

Pole-Ov-Temp

Pole over

temperature fault

Shut down the system for about

2 hours, then restart the system

to see if the fault is eliminated.

If the problem is not resolved,

please contact AlphaESS

customer service.

Cell-Ov-Volt

Cell over volt fault

Restart the system, switch the

system to the discharging state, If

the error is not eliminated, stop

any operation on the system and

contact AlphaESS customer

service.

Cell-Volt-Diﬀ

Cell volt diﬀerent

fault

Restart the system to see if the

fault is eliminated.

If the problem is not resolved,

please contact AlphaESS

customer service.

Disch-Low-Temp

Cell discharge

under

temperature fault

Conﬁrm that the ambient

temperature is higher than -10

℃

If it is lower than it, please turn

on the heating equipment such as

heater. If the ambient

temperature is higher than -10

℃

restart the system.

If the problem is not resolved,

please contact AlphaESS

customer service

Cell-Low-Volt

Cell under volt

fault

Restart the system to see if the

fault is eliminated

If the problem is not solved,

please contact AlphaESS customer

service

IR_Fail

Insulation

resistance fault

Switch oﬀ the battery MCCB and

measure the impedance of the

positive and negative poles of the

battery to the ground to see if it is

greater than 270KΩ and restart

the system.

If the problem is not solved. stop

any operation on the system and

contact AlphaESS customer

service.

Summary of Contents for Storion-T100

























Search results

Summary of Contents for Storion-T100

Reviews:

Related manuals for Storion-T100

Brands by name

Popular brands

Alpha ESS Storion-T100, Operation & Maintenance Manual

Search results

Summary of Contents for Storion-T100

Reviews:

Related manuals for Storion-T100

Brands by name

Popular brands