background image

ALMECO nv 

Air and water technologies

Royennestraat 51, B-7700 Moeskroen

[email protected] - www.almeco.eu

 

 Almeco

 NV-SA

 

Air and Water Technologies

 

Royennestraat 51, B-7700 Moeskroen

 

Tel.: +32 (0)56 85 40 80  

Fax: +32 (0)56 85 40 81

 

E-mail: [email protected] 

www.almeco.eu

 

16

EP10A

 compact blower

7.  WARRANTY & SERVICE EXCHANGE

 

Almeco warrants all products manufactured by ACI to be free of defects in material and workmanship for eighteen (18) 

 

months from the date of shipment. The warranty does not apply to drive belts, filter elements or connecting hose, unless 

 

authorised by an officer of ACI. Also, not covered under the warranty is normal wear and tear, neglect or misuse of the 

 

equipment, operation in an application not approved by Almeco and ACI, and alterations not performed by Almeco.

 

All items supplied by Almeco that are manufactured by others shall be warranted under the respective manufacturer’s 

 

policy. Motors and other items, for which a national service network is in place, should be sent directly to that 

 

manufacturer’s representative for the most prompt service. Almeco will provide any support required ensuring that 

 

warranty service by others is handled in a prompt and professional manner.

 

The Almeco warranty is limited to the repair or replacement of items shipped by Almeco. At no time will Almeco be liable  

 

for any of the costs to the buyer for labour, transportation or down-time resulting from defective equipment furnished by  

 

ACI, Almeco or our suppliers.

 

To comply with the Warranty the complete fan unit must be returned to Almeco. Disassembly of the fan will invalidate the

 warranty.

 

Service Address:

 

Our products are manufactured in compliance with applicable international standards and regulations. If you have any 

 

queries regarding the use of our products, or if you are planning a special application, please contact:

ALMECO nv 

Air and water technologies

Royennestraat 51, B-7700 Moeskroen

[email protected] - www.almeco.eu

Summary of Contents for ACI EP10A
















Reviews: