manualshive.com logo in svg

Allied Telesis GS950 PS Series, Installation Manual, Page: 41 / 108

Share
Download
Allied Telesis GS950 PS Series Installation Manual Download Page 41

GS950 PS V2 Series of Gigabit Ethernet PoE+ Switches Installation Guide

41

Warning

Power cord is used as a disconnection device. To de-energize 
equipment, disconnect the power cord. 

 

E3

Warning

Class I Equipment. This equipment must be earthed. The power 
plug must be connected to a properly wired earth ground socket 
outlet. An improperly wired socket outlet could place hazardous 
voltages on accessible metal parts. 

 

E4

Note

Pluggable Equipment. The socket outlet shall be installed near the 
equipment and shall be easily accessible. 

 

E5

Caution

Air vents must not be blocked and must have free access to the 
room ambient air for cooling. 

 

E6

This Warning applies only to the GS950/10PS V2 Switch.

Warning

Operating Temperatures. This product is designed for a maximum 
ambient temperature of 40°C. 

 

E7

This Warning applies to all GS950 PS V2 Switches except the 
GS950/10PS V2 Switch.

Warning

Operating Temperatures. This product is designed for a maximum 
ambient temperature of 45°C. 

 

E52

Note

All Countries: Install product in accordance with local and National 
Electrical Codes. 

 

E8

Summary of Contents for GS950 PS Series













































































































Reviews:

No comments