manualshive.com logo in svg

Alliance Laundry Systems UW100TV, Installation Manual

Share
Download
Alliance Laundry Systems UW100TV Installation Manual Download Page 6

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Safety Information

F8138601

4

IMPORTANT: Ensure that the recommended 

clearances for inspection and maintenance are 

provided. Never allow the inspection and 

maintenance space to be blocked.

Safety Decals

Safety decals appear at crucial locations on the 

machine. Failure to maintain legible safety decals 

could result in injury to the operator or service 

technician.
Use manufacturer-authorized spare parts to avoid 

safety hazards.

Operator Safety

The following maintenance checks must be performed 

daily:

1. Verify that all warning labels are present and 

legible, replace as necessary.

2. Check door interlock before starting operation of 

the machine:
a. Attempt to start the machine with the door 

open. The machine should not start.

b. Close the door without locking it and start the 

machine. The machine should not start.

c. Attempt to open the door while a cycle is in 

progress. The door should not open.

If the door lock and interlock are not functioning 

properly, disconnect power and call a service 

technician.

3. Do not attempt to operate the machine if any of 

the following conditions are present:
a. The door does not remain securely locked 

during the entire cycle.

b. Excessively high water level is evident.
c. Machine is not connected to a properly 

grounded circuit.

This machine must be installed, adjusted, 

and serviced by qualified electrical 

maintenance personnel familiar with the 

construction and operation of this type of 

machinery. They must also be familiar 

with the potential hazards involved. 

Failure to observe this warning may result 

in personal injury and/or equipment 

damage, and may void the warranty.

SW004

WARNING

Never touch internal or external steam 

pipes, connections, or components. 

These surfaces can be extremely hot and 

will cause severe burns. The steam must 

be turned off and the pipe, connections, 

and components allowed to cool before 

the pipe can be touched.

SW014

WARNING

NEVER insert hands or objects into 

basket until it has completely stopped. 

Doing so could result in serious injury.

SW012

WARNING

Operating the machine with severe out-of-

balance loads could result in personal 

injury and serious equipment damage.

W728

WARNING

Summary of Contents for UW100TV

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands