Alliance Laundry Systems UW100TV Installation Manual Download Page 4

Page: 4 / 48

F8138601

Safety Information

Explanation of Safety Messages

Precautionary statements (“DANGER,” “WARNING,”

and “CAUTION”), followed by specific instructions,

are found in this manual and on machine decals. These

precautions are intended for the personal safety of the

operator, user, servicer, and those maintaining the

machine.

Additional precautionary statements (“IMPORTANT”

and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used

to inform the reader of specific procedures where

minor machine damage will occur if the procedure

is not followed.

NOTE: The word “NOTE” is used to communicate

installation, operation, maintenance or servicing

information that is important but not hazard

related.

Important Safety Instructions

1. Read all instructions before using the washer.
2. Install the washer according the

INSTALLATION instructions. Refer to the

GROUNDING instructions in the

INSTALLATION manual for the proper

grounding of the washer. All connections for

water, drain, electrical power and grounding must

comply with local codes and be made by licensed

personnel when required. It is recommended that

the machine be installed by qualified technicians.

3. Do not install or store the washer where it will be

exposed to water and/or weather.

4. To prevent fire and explosion, keep the area

around machine free from flammable and

combustible products. Do not add the following

substances or textiles containing traces of the

following substances to the wash water: gasoline,

kerosene, waxes, cooking oils, vegetable oils,

machine oils, dry-cleaning solvents, flammable

chemicals, thinners, or other flammable or

explosive substances. These substances give off

vapors that could ignite, explode or cause the

fabric to catch fire by itself.

5. Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been

used for two weeks or more. HYDROGEN GAS

IS EXPLOSIVE. If the hot water system has not

been used for such a period, before using a

washing machine or combination washer-dryer,

turn on all hot water faucets and let the water

flow from each for several minutes. This will

release any accumulated hydrogen gas. The gas

is flammable, do not smoke or use an open flame

during this time.

6. To reduce the risk of an electric shock or fire, DO

NOT use an extension cord or an adapter to

connect the washer to the electrical power

source.

DANGER indicates an imminently

hazardous situation that, if not avoided,

will cause severe personal injury or

death.

DANGER

WARNING indicates a hazardous situation

that, if not avoided, could cause severe

personal injury or death.

WARNING

CAUTION indicates a hazardous situation

that, if not avoided, may cause minor or

moderate personal injury or property

damage.

CAUTION

To reduce the risk of fire, electric shock,

serious injury or death to persons when

using your washer, follow these basic

precautions:

W023

WARNING

Summary of Contents for UW100TV

















































Search results

Summary of Contents for UW100TV

Reviews:

Related manuals for UW100TV

Brands by name

Popular brands

Alliance Laundry Systems UW100TV, Installation Manual

Search results

Summary of Contents for UW100TV

Reviews:

Related manuals for UW100TV

Brands by name

Popular brands