manualshive.com logo in svg

Alliance Laundry Systems UW100TV, Installation Manual

Share
Download
Alliance Laundry Systems UW100TV Installation Manual Download Page 12

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Specifications and Dimensions

F8138601

10

Machine Dimensions 

Dimensional Clearances

Allow a minimum of 24 inches (60 cm) at the rear and 

6 inches (15.24 cm) at the sides for maintenance, 

inspection, and adjustment. Allow at least 6 inches 

(15.24 cm) between machines in multiple installations. 

NOTE: The dimensions shown here are for 

planning purposes only. They are approximate and 

subject to normal manufacturing tolerances. If 

exact dimensions are required for construction 

purposes, contact the distributor or the 

manufacturer. We reserve the right to make 

changes at any time without notice.

UWTV Models 

Crush hazard.

To avoid personal injury and/or property 

damage, do not tip the UW150 machine 

more than 25 degrees in any direction. 

W642

WARNING

(Refer to 

Figure 3

 and 

Figure 4

)

Dim

ension

35

60

80

100

125

150

in

mm

in

mm

in

mm

in

mm

in

mm

in

mm

A

30.125

765

35.625

905

41.125

1045

41.125

1045

48

1219

50.25

1277

B

1

33.375

848

36.625

930

41.5

1054

41.5

1054

48

1219

50.25

1277

C

23.75

603

28.25

718

29

737

29

737

29

737

32

813

D

43.625

1108

45

1143

51.5

1308

54.5

1384

58

1473

63

1600

E

2

.5

13

1

25

3

76

3

76

1.5

38

2.9

73

F

55.5

1410

64.5

1638

68.5

1740

68.5

1740

72

1829

79

2007

G

2

36

914

36

914

43.75

1111

43.75

1111

48

1219

56

1422

H

8

203

15.5

394

16.875

429

16.875

429

11.375

289

15.75

400

J

43.14

1096

49.8

1265

53.54

1360

53.54

1360

56.4

1433

62.85

1596

K

46.64

1185

53.3

1354

57.04

1449

57.04

1449

59.9

1521

66.35

1685

L

5.12

130

5.12

130.05

7.12

181

7.12

181

7.12

181

7.12

181

M

2.62

66

2.62

66

3.62

92

3.62

92

3.62

92

3.62

92

N

1.37

35

1.37

35

2.25

57

2.25

57

2.25

57

2.25

57

O

3.87

98

3.87

98

5

127

5

127

5

127

5

127

P

2.5

64

2.5

64

2.75

70

2.75

70

2.75

70

2.75

70

Q

2.5

64

2.5

64

3.5

89

3.5

89

3.5

89

3.5

89

1

Overhang dimensions for the optional starch dispenser are as follows:UW35TV, 3.88 inches (9.86 cm); UW60TV, 1.75 inches 
(4.45 cm); UW80TV and UW100TV, 0.33 inch (0.83 cm). (The starch dispenser does not overhang the UW125TV.) (No longer 

available.)

2

The overhang dimension for the premium wet clean module option (compatible with wet-clean-capable washer-extractors only) adds 
24 inches (60.96 cm) to combined machine dimensions E and G.

Table 1 

Summary of Contents for UW100TV

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands