background image

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

512042

6

Place the dryer in position, and adjust the legs until the 
dryer is level from side to side and front to back. The 
dryer must not rock.

Figure 3 

IMPORTANT: In mobile home installations, gas 
dryers MUST be permanently attached to the floor 
at the time of installation. Order No. 526P3 Dryer 
Installation Kit (available at extra cost) for a 
manufactured (mobile) home installation. Follow 
the instructions supplied with the kit.

Step 2: Connect Dryer Exhaust System

DRY2054N

1

Level

2

Leveling Leg

3

Dryer Base

DRY2054N

3

1

2

A clothes dryer produces combustible lint. 
To reduce the risk of fire and combustion 
gas accumulation the dryer MUST be 
exhausted to the outdoors.

W116

To reduce the risk of fire and the 
accumulation of combustion gases, DO NOT 
exhaust dryer air into a window well, gas 
vent, chimney or enclosed, unventilated 
area, such as an attic, wall, ceiling, crawl 
space under a building or concealed space 
of a building.

W045

WARNING

This gas appliance contains or produces a 
chemical or chemicals which can cause 
death or serious illness and which are 
known to the State of California to cause 
cancer, birth defects, or other reproductive 
harm. To reduce the risk from substances in 
the fuel or from fuel combustion, make sure 
this appliance is installed, operated, and 
maintained according to the instructions in 
this manual.

W115

To reduce the risk of fire, DO NOT use 
plastic or thin foil ducting to exhaust the 
dryer.

W354

WARNING

Summary of Contents for 512042R4





















Reviews: