background image

NOTE: All pads can be pressed in any sequence
without damaging control or tumble dryer. To stop
the tumble dryer at any time, open the door or press
STOP/RESET.

TMB1484N_SVG

Figure 41

NOTE: The window display will flash. Press STOP/
RESET twice (within three seconds) to end the cycle
and reset the control to idle status. To restart the
tumble dryer, CLOSE door and press START pad.

IMPORTANT: If the loading door or lint panel door is
opened during the cycle, the heating system will
shut off and the motor will stop. To restart the cycle,
both doors must be closed and START pad must be
pressed.

4.   When the cycle is complete, open door and remove the laun-

dry.

WARNING

To prevent the risk of fire, remove laundry imme-
diately in case of power failure.

W779

NOTE: This machine includes an anti-wrinkle/ ex-
tended tumble feature. After the drying cycle is
complete, the cylinder will tumble without heat ev-
ery few minutes. The intermittent tumbling will con-
tinue for one hour or until the door is opened.

 Single Drop Control

SD and SX Control Suffixes
1.   Select HIGH, MED, LOW or NO HEAT by turning the tem-

perature knob.

HIGH

Temperature 190°F [88°C]

MED

Temperature 160°F [71°C]

LOW

Temperature 130°F [54°C]

TMB2147N_SVG

Figure 42

2.   Insert the coin(s) in the coin slot.

TMB1492N_SVG 

Figure 43

3.   Press START button to start tumble dryer.

TMB2150N_SVG

Figure 44

IMPORTANT: To stop the tumble dryer at any time
during the cycle, OPEN DOOR. To restart the tumble
dryer, CLOSE door and press START button.

4.   When the cycle is complete, open door and remove the laun-

dry.

WARNING

To prevent the risk of fire, remove laundry imme-
diately in case of power failure.

W779

NOTE: This machine includes an extended tumble
feature. Starting 20 minutes after a cycle ends, the
cylinder will tumble for two minutes every hour
without heat, up to 18 hours or until door is opened.

 MDC Coin and Card Control

BB, BC, BG, BK, BL, BW, BX, BY and BZ Control Suffixes
1.   Select temperature by pressing the appropriate temperature

pad.

HIGH

Temperature 190°F [88°C]

MED

Temperature 180°F [82°C]

LOW

Temperature 160°F [72°C]

DELICATES

Temperature 130°F [54°C]

Operating Instructions

©

 Copyright, Alliance Laundry Systems LLC -

 DO NOT COPY or TRANSMIT

  74

  Part No: 70457901ENR15

Summary of Contents for 0904004427





































































































Reviews: