background image

English - 6

The following table gives checks and actions that you can perform if your machine does not operate correctly.

If these do not identify/remedy the problem, contact your service agent.

Warning: Switch off, remove spark plug cap before investigating fault.

Fault Finding

y

d

e

m

e

R

e

s

u

a

C

 

e

l

b

i

s

s

o

P

m

o

t

p

m

y

S

Mower leaves a ragged 

finish

Cylinder not correctly adjuster

Adjust the cylinder

Engine will not start

Engine is flooded

Spark plug lead not connected

Spark plug dirty

No oil

Leave for 10 – 15 minutes

Reconnect

See engine maintenance manual

Add oil

Engine stops

No petrol

Engine speed too low for conditions

Cutting cylinder obstructed

Engine does not stop

Refill tank

Move throttle

Turn off engine and clear 

obstruction

Throttle cable not correctly 

adjusted. Stop engine by removing 

spark plug lead and refer to the 

engine maintenance manual.

Cutting cylinder does not 

rotate

 

 

 

n TURFMECH Approved

a

 t

c

a

t

n

o

C

t

n

e

m

t

s

u

j

d

a

 t

c

e

r

r

o

c

n

I

Service Agent

Land drive does not 

engage

Incorrect adjustment/cable damaged

Contact an TURFMECH Approved 

Service Agent

Excessive vibration/noise Blade(s) or/and cylinder bearing damaged

Engine fault

Contact an TURFMECH Approved 

Service Agent

See engine maintenance manual

F016J10009A Page 18

Summary of Contents for BUCKINGHAM 20H















Reviews: